User manual ULINE ECHELON BI-2115

[. . . ] Use and Care Guide Ice Maker Model: BI2115 BI2115 1 Introduction Congratulations on your purchase of a U-Line refrigeration product. A pioneer in the field for more than 40 years, U-Line Corporation is the world's number one manufacturer of built-in, under-counter, specialty refrigeration and ice making products. U-Line dedicates 100% of its research and development to these products. The result: U-Line technology consistently leads the market with innovation, design, depth of product line and performance. [. . . ] · If any surface discoloring or rusting appears, clean it quickly with Bon-Ami® or Barkeepers Friend Cleanser® and a non-abrasive cloth. Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems. · Using abrasive pads such as ScotchbriteTM will cause the graining in the stainless steel to become blurred. · Rust that is not cleaned up promptly can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible. Defrosting Manual Defrost Models - Every Two Months (Minimum) WARNING DO NOT use any type of electrical heating device, ice pick, knife or other sharp instrument to defrost; this could damage the inner lining or refrigeration system and void the warranty. IMPORTANT The drain pan was not designed to capture the water created when manually defrosting. To prevent water from overflowing the drain pan, place towels or other absorbent materials on the bottom of the unit (Figure 5, 1), before defrosting. 1 Interior Cleaning (As Required) · Disconnect power to the unit. Clean the interior and all removed components using a mild non-abrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. These types of cleaners may transmit taste to the interior products and damage or discolor the interior. Place a towel or other absorbent material on bottom of unit (Figure 5, 1). Clean the interior and ice bucket using a mild non-abrasive detergent and warm water solution applied with a soft sponge or non-abrasive cloth. Dampen a soft sponge or non-abrasive cloth in clean water and wipe down the cabinet interior and ice bucket to remove any detergent residue. Rinse the sponge or cloth in clean water and repeat as necessary until the cabinet and ice bucket are clean. 2. NOTE: Screws are held in the grille by o-ring retainers, and will not come free of the grille. The condenser fins are SHARP and can be easily damaged. CAUTION DO NOT use any type of cleaner on the condenser unit. Clean the condenser coil (Figure 6, 2) using a soft brush with a "combing" action or vacuum cleaner. Position the grille to align the mounting screws with the holes in the cabinet. Reconnect power to the unit. IMPORTANT DO NOT place ice bucket in dishwasher. NOTE: To safeguard against contaminants in ice, discard first three batches of ice made after defrosting unit. Ice Maker Maintenance Inlet Screen Interval - Every Twelve Months The solenoid valve inlet screen must be cleaned at least once each year as follows: 1. Disconnect electrical power to the unit. Condenser Cleaning Interval - Every Three Months To maintain operational efficiency, keep the front grille free of dust and lint and clean the condenser every three months. Depending on environmental conditions, more or less frequent cleaning may be necessary. 2 WARNING Disconnect electric power to the unit before cleaning the condenser. To remove and replace the grille for access to the condenser fins, follow this procedure: Figure 7 1 ULIN_0054_A 1 4. Disconnect the hose connector (Figure 7, 1) from the water solenoid valve (Figure 7, 2). Use a tooth brush to gently clean any sediment from the inlet screen. 2 Figure 6 ULIN_0203_A 6. [. . . ] Adjust door (See MAINTENANCE; DOOR ALIGNMENT CHECK AND ADJUSTMENT and DOOR REVERSAL). Soft sounds from the fan and ice dropping from the ice maker will be heard. Set cube size smaller (See MAINTENANCE; ICE MAKER; ICE CUBE THICKNESS ADJUSTMENT). Set cube size smaller (See MAINTENANCE; ICE MAKER; ICE CUBE THICKNESS ADJUSTMENT). BI2115 15 This page intentionally left blank 16 BI2115 This page intentionally left blank BI2115 17 This page intentionally left blank 18 BI2115 U-Line Corporation Limited Warranty U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. [. . . ]