User manual ULINE ECHELON BI-2015

[. . . ] É c h e l o nTM TM U S E R M A N U A L U-LINE CORPORATION LIMITED WARRANTY U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year warranty period for all U-Line products U-Line shall: (1) at U-Line's option, repair any product or replace any part of a product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part. During years two through five of the warranty period for the sealed system, U-Line shall:. (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii)and Canada, U-Line shall cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. [. . . ] Be careful not to lose door closers (see Figure 12). 1/8" 2. DOOR001 Figure 15 3. With door upside-down, loosen but do not remove the two hinge plate screws. UL310 Figure 16 13 User's Manual CUSTOM DOOR PANELS Two types of custom door panels can be installed on your U-Line unit to harmonize with or accent the surrounding decor. FULL OVERLAY DOOR PANEL A full overlay door panel completely covers the door frame and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit which contains the Panel Preparation Document for building and installing a full overlay panel. Full Overlay Panel Dimensions Model 2015 Series 2075 Series A 29-7/8" 29-7/8" B 14-3/4" 23-3/4" CUSTOM INSERT DOOR PANEL A custom door panel can be inserted into the door frame to better match the surrounding decor. Custom door panels can be flat or raised, as long as the maximum panel thickness where inserted into the door reveal (channel) is B 1/4" thick. For raised panels, the depth of the reveal is 1/4" on all four sides. Custom Insert Door Panel Dimensions Model 2015 Series 2075 Series A A 28­5/32" 28­5/32" B 14­1/32" 23­1/32" Door panel insert must not weigh more than 20 lbs. 14 Install the insert as follows: !Start in the middle and pull outward, moving toward the edge (see Figure 19). Pull handle up and off. UL132 UL310 2. Figure 17 3. 4. Figure 18 NOTE Use care not to bend light switch bracket (where installed), located on door bottom when installing door insert. 5. UL117 Slide custom door panel insert into 1/4 inch channel in door front. Figure 19 15 User's Manual 6. Holding door gasket out of the way, replace handle on door making sure it is seated properly on insert and that screw holes line up. Starting at the corners and working inward, push door gasket into place on door. 9. BUILT-IN INSTALLATION Your U-Line product has been designed for either free-standing or builtin installation. When built-in, your U-Line product does not require additional air space for top, sides, or rear. However, the front grille must NOT be obstructed. NOTE Required for ease of installation, removal and door opening, you must allow an additional 1/4" to width of unit. Unit Dimensions Model 2015 Series 2075 Series Width 14-15/16" 23-15/16" Height 34-1/8" 34-1/8" Depth* 24" 24" * For full overlay door panels, add 3/4". INITIAL START-UP Once installation is complete, the unit is ready for initial start-up and operation. CONTROL SETTINGS-COMBO/REFRIGERATOR Models 2015R, 2075R and 2075RF are turned ON with the control knob located on the grille. Models 2015R, 2075R and 2075RF turn OFF when the temperature control is turned counterclockwise all the way toward warmer until it stops (until "click" is heard). 16 4 3 2 1 WARMER 5 6 7 COLDER UL315 Figure 20 CONTROL SETTINGS - COMBO/ICE MAKER TEMPERATURE CONTROL KNOB Models BI 2015 and 2075FF are turned ON with the ON/OFF switch recessed in the front grille (see Figure 21). In these units, the control dial is used only for temperature control. 4 3 2 1 WARMER 5 6 7 COLDER OFF ON ON/OFF SWITCH UL316B Figure 21 1. Plug the appliance cord into a 115V polarized and grounded electrical outlet. As soon as the ice maker mold reaches the proper temperature, the ice maker mechanism will fill the mold with water. Allow 2 hours for frost free models. It is possible that dirt or scale will dislodge in the water line. Always throw away all ice cubes made during the first two to three hours of operation. 17 User's Manual NORMAL OPERATION On units with refrigerator sections, the unit has been designed to achieve a fresh food temperature of approximately 38°F. [. . . ] The crisper may be completely removed for cleaning. UL304 Figure 31 LIGHT BULB REPLACEMENT Light bulb replacement ÉchelonTM series is simple. in the 1 TAB Remove the light housing cover by sliding the cover toward the tab, swinging the end opposite the tab down and pulling down and away (see Figure 32). Replace the light housing cover by inserting the tab FIRST, sliding the cover toward the tab and pushing up the other end. WARNING DO NOT use any type of electrical heating device, ice pick, knife, or other sharp instrument to defrost. [. . . ]