User manual TRICITY AW870

[. . . ] When you are lighting any burner check that it is lit before you leave the appliance. When turning off a burner, do not leave the appliance until the flame has gone out. Never place plastic or any other material that may melt in or on the oven. Ensure cooking utensils are large enough to contain foods to prevent spillages and boil overs. [. . . ] Always add milk and milk products, for example cream towards the end of cooking to prevent them from curdling. Reheating Cool left over food quickly and then put it in the fridge. Only reheat food once. 16 CARE AND CLEANING Before cleaning always allow the appliance to cool down. CLEANING MATERIALS Before using any cleaning materials on your appliance, check that they are suitable and that their use is recommended by the manufacturer. Cleaners that contain bleach should NOT be used as they may dull the surface finishes. Harsh abrasives must also be avoided. CLEANING THE OUTSIDE OF THE APPLIANCE Do not use abrasive cleaning materials e. g. Hob Brite, Brillo pads or scourers on painted or printed finishes as damage may occur. Regularly wipe over the control panel, doors and appliance sides using a soft cloth and hot soapy water. Stainless Steel cream cleaners are abrasive and should be avoided as they may dull the surface finish. Any spillage on the stainless steel finish must be wiped off immediately. Do not attempt to remove any of the control knobs from the appliance as this may cause damage and is a safety hazard. CLEANING THE CONTROL KNOBS AND HANDLES It is strongly recommended that only hot soapy water is used for cleaning the control knobs and handles. ANY OTHER CLEANING MATERIALS MAY DULL THE SURFACE FINISH. CLEANING THE HOB Clean the hotplate top using a mild abrasive. You can remove the pan supports, burner caps and burner crowns to clean them. Check that the recommended temperatures and shelf positions are being used. Be prepared to adjust the temperature up or down slightly to achieve the results you want. You can do this by making sure the other gas appliances such as central heating or gas fires are working. Due to the design of the burner the flame can appear to be orange /yellow (flame disturbance) in certain areas of the burner this is a natural occurrence. Check that the burner is dry and that food spillage or cleaning fluids are not present on the burner. This can be dried with a cloth and stubborn marks cleaned away with a dry nylon brush (old toothbrush etc). It is natural for the burners to emit noise as the gas is being drawn through the burner and may reduce as they heat up. This is a natural occurrence when the burner is alight and does not affect the performance of the burner. It is normal for some metal parts on the cooker to produce noise when in use, this is due to expansion and contraction when heating up and cooling down. The oven is not cooking evenly. The oven temperature is too high or too low. The hob burners will not light. The flame colour is orange/yellow. The burner is not igniting or only partially lighting. The burner sounds noisy. The burner is emitting a popping sound. Noise. 19 SERVICE AND SPARE PARTS In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning:- 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk. Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working?". [. . . ] Mark off 250mm from the left hand side of the appliance as shown in dimension 'A', Fig 4a. Draw a line from the front edge of the feet (see Fig. 3a) and remove appliance from its position. Mark off dimension 'B' (see Fig. 4a) back from this line on the centre line of the bracket to locate the front edge of the lower bracket. Fix lower bracket (with two fixing holes) to the floor then measure the height from floor level to engagement edge on back of appliance, dimension 'C' of Fig. [. . . ]