User manual TRENDNET TW100-BRF114

[. . . ] Table of Contents CHAPTER 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 TW100-BRF114 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Physical Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the connection currently exists, the "Disconnect" button can be used to break the connection. Normally, it is not necessary to use the Connect and Disconnect buttons unless the setting "Connect automatically, as required" is disabled. IP Address Connection Status Connection Log Connection Log · · Buttons Connect If not connected, establish a connection to Telstra Big Pond. The Connection Log shows status messages relating to the existing connection. The Clear Log button will restart the Log, while the Refresh button will update the messages shown on screen. 38 Operation and Status Disconnect Clear Log Refresh If connected to Telstra Big Pond, terminate the connection. Update the data on screen. Connection Details - SingTel RAS If using the SingTel RAS access method, a screen like the following example will be displayed when the "Connection Details" button is clicked. Figure 25: Connection Details - SingTel RAS Data - SingTel RAS Screen Internet RAS Plan Physical Address The RAS Plan which is currently used. The hardware address of this device, as seen by remote devices on the Internet. (This is different to the hardware address seen by devices on the local LAN. ) The IP Address of this device, as seen by Internet users. The IP Address of the remote Gateway or Router associated with the IP Address above. This will show "Enabled" or "Disabled", depending on whether or not this device is functioning as a DHCP client. If "Enabled" the "Remaining lease time" field indicates when the IP Address allocated by the DHCP Server will expire. The lease is automatically renewed on expiry; use the "Renew" button if you wish IP Address Network Mask Default Gateway DNS IP Address DHCP Client 39 TW100-BRF114 User's Guide to manually renew the lease immediately. Buttons Release/Renew Button will display EITHER "Release" OR "Renew" This button is only useful if the IP address shown above is allocated automatically on connection. · If the ISP's DHCP Server has NOT allocated an IP Address for the TW100-BRF114, this button will say "Renew". Clicking the "Renew" button will attempt to re-establish the connection and obtain an IP Address from the ISP's DHCP Server. If an IP Address has been allocated to the TW100-BRF114 (by the ISP's DHCP Server), this button will say "Release". Clicking the "Release" button will break the connection and release the IP Address. · Refresh Update the data shown on screen. Connection Details - Fixed/Dynamic IP Address If your access method is "Direct" (no login), a screen like the following example will be displayed when the "Connection Details" button is clicked. Figure 26: Connection Details - Fixed/Dynamic IP Address Data - Fixed/Dynamic IP address Screen Internet Physical Address The hardware address of this device, as seen by remote devices on the Internet. (This is different to the hardware address seen by devices on the local LAN. ) The IP Address of this device, as seen by Internet users. The IP Address of the remote Gateway or Router associated with the IP Address above. 40 IP Address Network Mask Default Gateway Operation and Status DNS IP Address DHCP Client The IP Address of the Domain Name Server which is currently used. This will show "Enabled" or "Disabled", depending on whether or not this device is functioning as a DHCP client. If "Enabled" the "Remaining lease time" field indicates when the IP Address allocated by the DHCP Server will expire. The lease is automatically renewed on expiry; use the "Renew" button if you wish to manually renew the lease immediately. Buttons Release/Renew Button will display EITHER "Release" OR "Renew" This button is only useful if the IP address shown above is allocated automatically on connection. [. . . ] Generate a read-only list of all entries in the Static Routing table. Configuring Other Routers on your LAN It is essential that all IP packets for devices not on the local LAN be passed to the TW100BRF114, so that they can be forwarded to the external LAN, WAN, or Internet. To achieve this, the local LAN must be configured to use the TW100-BRF114 as the Default Route or Default Gateway. Local Router The local router is the Router installed on the same LAN segment as the TW100-BRF114. This router requires that the Default Route is the TW100-BRF114 itself. Destination IP Address Network Mask Gateway IP Address Metric Normally 0. 0. 0. 0, but check your router documentation. [. . . ]