User manual TRENDNET TW-200

[. . . ] Web Cruiser User's Guide TW200 TW400 P/N 9560660037 Sensitive Information This page contains a security password. If the device password is lost or forgotten, this meta-password will allow access to the device configuration. This meta password will function only in Terminal Configuration mode. [+-*/] Please remove this page and treat it with the same discretion you would treat your regular password. Carelessness in password policy may lead to serious compromises in system security. FCC Statement: This device complies with Part 15 of the FCC Rules. [. . . ] Note that although the device supports up to 50 shared users, only 18 can be entered here. 28 Configuration Programs [ E-mail gateway User Information ] User name Password Mail account Unrouted Mail 1)> 1 No 2) 1 No 3) 1 No 4) 1 No 5) 1 No 6) 1 No 7) 1 No 8) 1 No 9) 1 No 10) 1 No 11) 1 No 12) 1 No 13) 1 No 14) 1 No 15) 1 No 16) 1 No 17) 1 No 18) 1 No ----------------------------------------------------- See User Information on page 20 for information on these fields. To enter data: · TAB to the desired field · · · press ENTER type the data press ENTER. Repeat for the next field. 29 Error!User Guide Browser Mode Configuration Overview This method uses your existing WEB browser. Most WEB browsers should work, provided they support tables and forms. must be installed on your LAN first. Connection To establish a connection from your PC to the device: · · Start your WEB browser In the Address box, enter "HTTP://" and the IP Address of the Error!Reference source not found. , as in the following example: HTTP://192. 168. 0. 1 Password You should then see the first screen, which will prompt you for a password. If no password has been set, just click OK to continue to the Start screen. The Start screen contains helpful information for first-time users. Navigation & Data Input Most screens contain a navigation bar on the left of the screen allows you to move about. Remember that changing to another screen without clicking "OK" does NOT save any changes you may have made. HTML uses "forms based input" which means you must send (submit) the form (by clicking a button) or your data will be ignored. 30 Configuration Programs Port Configuration Selecting the Ports hyperlink will display a screen like the following. Figure 5: Select Port Select the port and the required operation, and click OK to move to the Port Configuration screen. 31 Error!User Guide Figure 6: Port Configuration Refer to page 13 for details of these settings. Advanced Port Settings Clicking the Advanced Port Settings hyperlink at the top of the screen will take you to the following screen. 32 Configuration Programs Figure 7: Advanced Port Settings Refer to page 15 for details of these settings. Port Status Screen The Port Status screen is reached by selecting Status/Test on the Select Port screen shown in Figure 5. An example Port Status & Test screen is shown below. 33 Error!User Guide Figure 8: Port Status &Test Current Port Physical Link Displays the current port. The connection speed over the phone line, between your modem and the number dialed. PPP Link Serial Line Speed Phone Line Speed 34 Configuration Programs PPP IP Address The IP Address at the other end of the PPP connection, if one has been established. This shows the commands sent to the modem, and any status messages returned by the modem. Note that this is not "live"; you must select Refresh and then click OK to update the information. · Hang Up will hang up the modem, breaking an existing connection. Dial will establish a connection to the ISP, if no connection currently exists. Refresh will update the information shown on screen. Modem Log Operations · · · You must click OK to have the operation performed 35 Error!User Guide Advanced Setup Selecting the Advanced hyperlink from the navigation bar will reveal a screen like the following. Figure 9: Advanced Settings See page 17 for details of these settings. 36 Configuration Programs Status Screen The Status screen can be reached with the hyperlink on the navigation bar. The following example is for the 4-port model. Figure 10: Status Screen No. [. . . ] Pause for 3 seconds Send the string password, where password is your password, followed by a carriage return. Send the string "GO PPPCONNECT", followed by a carriage return character. Pause for 100 ms between each character. wait 3000 send 100 "password\r" wait 60000 "!" Send 100 "GO PPPCONNECT\r" 73 E Terminal Programs This section explains how to configure and use a Terminal (Communications) program, as required to perform the Terminal Mode Configuration described on page 21. Windows 95 The terminal communications program provided with Windows 95 is called HyperTerminal. Click and follow the selection Start Menu-Programs-Accessories-HyperTerminal. [. . . ]