User manual TRENDNET TVP-224HR

[. . . ] 1 FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed in accordance with the instruction manual, may cause harmful interference to radio communication. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at the user's own expense. CE Declaration of conformity This equipment complies with the requirements relating to electromagnetic compatibility, EN 55022 class A for ITE and EN 50082-1. [. . . ] This feature allows you to manage the TVP-221HR via the Internet using your Web Browser or Telnet. The firmware (software) in the TVP-221HR can be upgraded using your Web Browser. Upgrade Firmware Access Control Administration Password Setup / Login The Administration Password Page allows you to change your password on the TVP-224HR Figure 25: Administration Password Setup Screen 51 TVP-224HR User's Guide Data ­ Administration Password Setup Admin Login Old Password New password Enter the old password Enter the new password here. If a password is set, the password will be required in order to change the configuration. Click on OK to confirm new password Retype New password Buttons OK Note Changes to the password from the Web UI and Telnet are effective immediately unless trying to use the new password set in Web UI and Telent from Console port. In this case, you would have to reboot the GW before the password would take effect. Figure 26: Password Dialog Enter the default "User Name" and the "Password" you set on the Administration Password Setup screen above. Remote Administration Remote Administration allows you to connect to this interface via the Internet, using your Web browser or Telnet. By default, both services are activated. 52 TVP-224HR User's Guide Figure 27: Remote Administration Screen Data - Remote Administration Screen Information Information To establish a connection from the Internet: 6. In the "Address" or "Location" field, enter "HTTPS//" (NOT "HTTP//"), the Internet IP address of this device (NOT the LAN IP address), and the port number, as follows: HTTPS://ip_address:port_number Where: ip address is the Internet IP address of this device. Settings HTTP Check this to allow web administration/management via the Internet. If Disabled, this device will ignore management connection attempts from the Internet. Check this to allow Telnet administration/management via the Internet. If Disabled, this device will ignore management connection attempts from the Internet. To manage this device via the Internet, you need to know the IP Address of this device, as seen from the Internet. However, if you are using a Dynamic IP Address, this value can change each time you connect to your ISP. There are 2 solutions to this problem: Have your ISP allocate you a Fixed IP address. Use the DDNS feature (Internet menu) so you can connect using a You should then be prompted for the password for this device. (You must assign a password!) Telnet IP Address 53 TVP-224HR User's Guide Domain Name, rather than an IP address. |Trusted Telnet Clients Ping Reply This allows you to restrict remote access by IP address. If enabled, this service allows the TVP-224HR to reply when pinged. To connect from a remote PC via the Internet 1. Ensure your Internet connection is established, and start your Web Browser. In the "Address" bar, enter "HTTPS://" followed by the Internet IP Address of the TVP224HR. (After the IP Address, enter ":" followed by the port number. ) e. g. HTTPS://123. 123. 123. 123:8080 This example assumes the WAN IP Address is 123. 123. 123. 123, and the port number is 8080. Upgrade Firmware Use this screen to upgrade your TVP-224HR's firmware. [. . . ] When an incoming phone number matches the phone number of the hunt group, the TVP224HR attempts to terminate the call at each of the destinations in the hunt group one at a time until a call is successfully completed. Plan how destinations are to be grouped and fill out the hunt table worksheet, then use the CLI command atpm hadd hunt_group_id hunt_type dest_id . . . The hunt_group_id in the command corresponds to the Hunt Group ID in the worksheet, the hunt_type corresponds to the Hunt Type (1 or 2), the dest_id . . . You may alternatively use the web browser to add hunt groups to the hunt group table. Hunt Type Hunt Group ID 1 2 List of Destination IDs 124 TVP-224HR User's Guide ATPM Address Table Each phone number to be recognized by the TVP-224HR must have its first digits match an entry in the address table. [. . . ]