User manual TRENDNET TV-IP410

[. . . ] PREFACE The Pan/Tilt Internet Camera Server (TV-IP410) /Wireless Pan/Tilt Internet Camera Server (TV-IP410W) provides real-time security surveillance over a large viewing area. Monitor people in your camera's viewing field and manage the camera from any Internet connection. See more with one Internet camera--remotely pan the camera side-toside a remarkable 330 degrees and tilt up-and-down 105 degrees. The TV-IP410/TV-IP410W provides high quality video streams over a secure or wireless connection. [. . . ] When the detecting area is enabled, you can use the mouse to move the detecting area and change the area coverage. - Name: Assign a name to the detecting area. - Threshold: Move the slide bar to adjust the level for detecting motion to record video. NOTE Sliding the Threshold bar to the right will decrease the sensitivity of motion detection; sliding the Threshold bar to the left will increase the sensitivity of motion detection - 48 - 4. 9 Event Config The Event Config menu contains five sub-menus that provide the commands to configure event profiles. Event Configuration >> General Setting - Snapshot/Recording Subfolder: You can assign a descriptive name for the subfolder to save the captured image/video files. - GPIO Trigger Out Retention Time Per Event: Limit the retention time of the GPIO Trigger Out function. Event Configuration >> Arrange Schedule Profile - 49 - This sub-menu displays the scheduled profile(s). To customize the profile, click Add and then enter a descriptive name for the profile in the prompt dialog window. To delete the profile, select the profile in the list and click Delete. - 50 - - Profile Name: Display the profile name that you select in the Schedule Profiles list. - Weekdays: Select the weekday(s) that you want to separately assign in the schedule profile. The weekday that has been assigned will be displayed with green color. - Time List: Display the time period that you have assigned within the selected weekday. To assign the same time period to every weekday, click Add this to all weekdays; click Delete this from all weekdays to remove the selected time period from every weekday. - Start/End Time: Enter the start and end time and then click Add to assign a time period within in the selected weekday. Event Configuration >> Motion Detect Trigger Select the Enable option to enable the motion detect trigger function of the camera, so that you can set Trigger Out function or send captured images within the detecting area to the FTP server and email receiver. You have to configure corresponding settings, such as FTP server and email server, to enable this feature. - 51 - - Schedule Profile: Select a schedule profile from the pull-down list. - Action: Set the Trigger Out function or select the destination of the captured images: Send Email, or FTP Upload. NOTE Setting the Pre-event/Post-event time for sending email or uploading to FTP may cause the system overloads. Event Configuration >> Schedule Trigger You can separately configure the schedule for trigger function of the camera by Email or FTP. Select the Enable option on each item, and - 52 - then select a Schedule Profile from the pull-down list and set the Interval time. Event Configuration >> GPIO Trigger Select the Enable option to enable the GPIO trigger function of the camera, so that you can set Trigger Out function or send captured images within the detecting area to the FTP server or email receiver, . You have to configure corresponding settings, such as FTP server and email server, to enable this feature. - 53 - - Schedule Profile: Select a schedule profile from the pull-down list. - Action: Set the Trigger Out function or select the destination of the captured images: Send Email, or FTP Upload. NOTE Setting the Pre-event/Post-event time for sending email or uploading to FTP may cause the system overloads. - 54 - 4. 10 Tools The Tools menu provides the commands that allow you to restart or reset the camera. You can also backup and restore your configuration, and upgrade the firmware for the camera. Factory Reset Click Reset to restore all factory default settings for the camera. System Reboot Click Reboot to restart the camera just like turning the device off and on. The camera configuration will be retained after rebooting. Configuration - 55 - You can save your camera configuration as a backup file on your computer. Whenever you want to resume the original settings, you can restore them by retrieving the backup file. - Backup: Click Get the backup file to save the current configuration of the camera. [. . . ] WPA2 uses the government-grade AES encryption algorithm and IEEE 802. 1X-based authentication, which are required to secure large corporate networks. WPA2 - 98 - Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TV-IP410/TV-IP410W­ 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. [. . . ]