User manual TRENDNET TV-IP322P V1.01

[. . . ] PREFACE Thank you for purchasing the TV-IP322P SecurViewTM Outdoor PoE Megapixel Day/Night Internet Camera, a standalone system that can be connected directly to an Ethernet or Fast Ethernet network. The camera is equipped with a 2-megapixel CMOS sensor, allowing you to capture high quality image with the resolution of up to 1280 x 1024. Additionally, the camera features the IR (Infrared) LEDs and ICR function (IR Cut Filter). The ICR function enables the camera to capture the clear image under sunlight and increase the amount of light for IR LEDs in the dark by changing the filter automatically. [. . . ] Threshold: Move the slide bar to adjust the level for detecting motion to record video. Sliding the Threshold bar to the right will decrease the sensitivity of motion detection; sliding the Threshold bar to the left will increase the sensitivity of motion detection. NOTE - 57 - 4. 8 Event Configuration The Event Config menu contains five sub-menus that provide the commands to configure event profiles. - 58 - 4. 8. 1 Event Configuration >> General Setting General Snapshot/Recording Subfolder: You can assign a descriptive name for the subfolder to save the captured image/video files. Storage Recording Time Per Event: Limit the recording time while you are using the Network Storage solution. GPIO Trigger Out Retention Time Per Event: Limit the retention time of the GPIO Trigger Out function. 4. 8. 2 Event Configuration >> Arrange Schedule Profile Schedule Profile: This sub-menu displays the scheduled profile(s). To customize the profile, click Add and then enter a descriptive name for the profile in the prompt dialog window. After entering the profile name, click OK and the profile is added to the Schedule - 59 - Profiles list. To delete the profile, select the profile in the list and click Delete. Profile Name: Display the profile name that you select in the Schedule Profiles list. Weekdays: Select the weekday(s) that you want to separately assign in the schedule profile. The weekday that has been assigned will be displayed with green color. Time List: Display the time period that you have assigned within the selected weekday. To assign the same time period to every weekday, click Copy this to all weekdays; click Delete this from all weekdays to remove the selected time period from every weekday. Start/End Time: Enter the start and end time and then click Add to assign a time period within in the selected weekday. - 60 - 4. 8. 3 Event Configuration >> Motion Detect Trigger Motion Detect Trigger: Select the Enable option to enable the trigger function of the camera, so that you can send captured images within the detecting area to the FTP server, email receiver, or the Network Storage server. You have to configure corresponding settings, such as FTP server and email server, to enable this feature. Please note that you have to configure the related settings before enabling these features. Action: Set the Trigger Out function or select the destination that the captured images will be sent to: , or Record to SD Card, Record to Network Storage, Send Email, FTP Upload, or Instant Message. - 61 - 4. 8. 4 Event Configuration >> Schedule Trigger You can separately configure the schedule for trigger function of the camera by Email, FTP, or Network Storage. Select the Enable option on each item, and then select a Schedule Profile from the pull-down list and set the Interval time. NOTE If the setting value of the Network Storage Recording Time Per Event option in General Setting is longer than the Interval time in Network Storage Schedule, the recorded file will be a continuous video clip. For example, if you set the Network Storage Recording Time Per Event as 10 seconds and the Interval as 5 seconds, recorded file becomes a non-stop video clip because the camera will record a 10-second video clip every 5 seconds. - 62 - 4. 8. 5 Event Configuration >> GPIO Trigger GPIO Trigger: Select the Enable Trigger In 1/2 option to enable the GPIO trigger function of the camera, so that you can set Trigger Out function or send captured images within the detecting area to the SD card, FTP server, email receiver, Network Storage server, or send an instant message. Action: Set the Trigger Out function or select the destination that the captured images will be sent to: Record to SD Card, Record to Network Storage, Send Email, FTP Upload, or Instant Message. - 63 - 4. 9 Tools The Tools menu provides the commands that allow you to restart or reset the camera. You can also backup and restore your configuration, and upgrade the firmware for the camera. - 64 - Factory Reset: Click Reset to restore all factory default settings for the camera. You can also do the physical reset by press the reset button on the camera. Remove the front cover of the camera and press the reset button as indicates below. System Reboot: Click Reboot to restart the camera just like turning the device off and on. Configuration: You can save your camera configuration as a backup file on your computer. Whenever you want to resume the original settings, you can restore them by retrieving the backup file. [. . . ] TV-IP322P ­ 3 Years Limited Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. [. . . ]