User manual TRENDNET TV-IP201

[. . . ] TABLE OF CONTENTS ABOUT THIS GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FEATURES AND BENEFITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 UNPACKING THE PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 SYSTEM REQUIREMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PHYSICAL DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. HARDWARE INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 ATTACHING THE CAMERA TO THE STAND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 CONNECTING THE ETHERNET CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 ATTACHING THE POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 3. SECURITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4. [. . . ] When you click the Record button and select Manual Record, it will start recording. If you select Schedule Record or Motion Record, the system will record the video clip according to the settings in System Configuration. 58 Playing Recorded Video The recorded video clips are saved in your computer, and can be played using Windows Media Player. To start playback, simply click the Play button on the panel, and the following dialog screen will appear, allowing you to select the file to playback. Select one file to playback. The folder that stores the recorded file. Select the recorded file in the computer, and then click OK. 59 Configuring the System Clicking the System Configuration button on the panel allows you to configure the system settings, and the System Configuration Screen will appear in the View Window as shown below. Once configured, click Save to save the settings, and then click the System Configuration button again to exit configuration. System Configuration Screen 60 Camera Configuration In this field, you can add/delete the camera (as described in the previous section). Also, you can configure the following settings: Web Configuration In the left column, selecting the Web Configuration item will launch the Web Configuration Utility in View Window. You can configure these settings according to the description in Chapter 5, Using the Camera. Click Back to exit the Web Configuration Utility. 61 Motion Configuration-1 The Motion Configuration-1 item provides the commands for motion detection control. Before configuring, you should select one camera from the pull-down menu. Select one camera. Select Custom region. Region 1. Region 2. - Detect Region: · Full picture ­ When you select this option, the camera will monitor the whole area. · Custom region ­ Click Add Region, and then use mouse to draw an area in the view screen; when some motion detected within the area, the camera starts 62 - recording automatically. Sensitivity Level: Move the slide bar to adjust the sensitivity level for detecting motion to record video. Motion Configuration-2 The Motion Configuration-2 item allows you to configure to the alarm and e-mail setting. - Invoke Alarm: Select this option to enable alarm when some motion detected by the system. 63 - - - Send e-mail: When this option is checked, click the Mailing Configuration in the left column to enter the required information (see the following section). Click Browse music file to select the desired music, and set the Interval time. Trigger1 active: You can check this option to set the Trigger-On holding time. Tools The Tools item allows you to configure to the alarm and e-mail setting. 64 - - - Reset: Restore the original setting of your camera. Update Firmware: When new firmware is available, you can upgrade it using this option. Click Browse to find the firmware file, and then click Update. 65 Mailing Configuration When Motion Detection function is enabled and the Send e-mail option is checked, you should enter the required information in the respective fields. - Mail Server: Enter the mail server address that is used to send your e-mail. User Name/Password: Enter the user name/password to login the mail server. Interval Time: Enter a number in this box to setup the time (in second) to send e-mail regularly. 66 Proxy Server Check the Proxy Server option and enter the required settings in the Address and Port boxes to enable and use the Proxy Server function. 67 Recording Configuration In this field, you can configure the storage settings. - Log Storage: · Reserved HDD Space For MS-Windows OS ­ You can reserve 500 MB to 10000 MB hard disk space for the program. · Each Recording File Size ­ If the recorded video files reach the file size limit, video images will be recorded into another file automatically. · Storage List ­ The destination folder to save the recorded video file can be specified here. Click Modify to change the current path setting; click Add to add a new 68 - - destination folder; click Delete to remove a selected path setting. Please note that you are not allowed to delete a path setting if there is only one setting in the list. Recycle: You can check this option to clear the files when the unreserved space of your hard disk is filled. [. . . ] It was developed y the Department of Defense to connect different computer types and led to the development of the Internet. Transceivers can also be used to join a segment that uses one medium to a segment that uses a different medium. On a 10BASE-5 network, the transceiver connects the network adapter or other network device to the medium. Transceivers also can be used on 10BASE-2 or 10BASE-T networks to attach devices with AUI ports. Transceiver U UDP The User Datagram Protocol is a connectionless protocol that resides above IP in the TCP/IP suite The upper-layer protocol refers to Application Layer protocols such as FTP, SNMP, and SMTP. [. . . ]