User manual TRENDNET TV-IP110

[. . . ] PREFACE Thank you for purchasing the TV-IP110/TV-IP110W Wire/Wireless Internet Camera Server, a powerful and high-quality image network camera. The camera can be installed as a standalone system within your application environment easily and quickly, and supports remote management function so that you can access and control it using a Web browser on your PC. This guide will provide you more information of instruction and illustrations on how to use your camera, which includes: Chapter 1 Introduction to Your Camera describes the features of the camera. Hardware Installation helps you install the camera according to your application environment. [. . . ] - Action: Select the destination that the captured images will be sent to: Send Email, or FTP Upload. Event Configuration >> Schedule Trigger - 49 - You can separately configure the schedule for trigger function of the camera by Email or FTP. Select the Enable option on each item, and then select a Schedule Profile from the pull-down list and set the Interval time. - 50 - 4. 9 Tools The Tools menu provides the commands that allow you to restart or reset the camera. You can also backup and restore your configuration, and upgrade the firmware for the camera. - 51 - Factory Reset Click Reset to restore all factory default settings for the camera. System Reboot Click Reboot to restart the camera just like turning the device off and on. The camera configuration will be retained after rebooting. Configuration You can save your camera configuration as a backup file on your computer. Whenever you want to resume the original settings, you can restore them by retrieving the backup file. - Backup: Click Get the backup file to save the current configuration of the camera. - Restore: Click Browse to locate the backup file and then click Restore. Update Firmware This item displays the current firmware version. You can upgrade the firmware for your camera once you obtained a latest version of firmware. - Select the firmware: Click Browse to locate the backup file (xxx. pck) and then click Update. Factory reset and IP Setup are required after firmware update. NOTE Make sure to keep the camera connected to the power source during the process of upgrading firmware. Otherwise, the camera might be damaged because of failure of upgrading firmware. - 52 - 4. 10 Information The Information menu displays the current configuration and events log of the camera. Device Info Display the Basic, Video, Network, and Wireless settings of the camera. System Log The Logs table displays the events log recorded by the system. - 53 - CHAPTER 5 SECURVIEWTM SOFTWARE This Chapter describes detail instructions on operating SecurViewTM software, a useful friendly application for ease of control and navigation requirement. 5. 1 1. INSTALLATION Insert the Installation CD-ROM into your computer's CD-ROM drive to initiate the Auto-Run program. 2. Click the SecurView from the Auto-Run menu screen. - 54 - NOTE To use SecurViewTM, you must have Microsoft . NET Framework 2. 0 installed in the computer. The setup wizard will detect it and, if the program is not installed yet, ask you to install it during the process of installing SecurViewTM. - 55 - 3. Then SecurView Setup Wizard will appear. Click "Next" when the Welcome to the SecurView Setup Wizard appears. 4. Click "Browse" to choose the desired destination location. By default, the destination location is C:\Program Files\TRENDnet\SecurView. Then Click "Next". - 56 - 5. Click "Next" to confirm the SecurView software to be installed to the computer. - 57 - 6. When the Installation Complete window appears, click "Close". 7. After installing the IPSetup utility, the application is automatically installed to your computer, and creates a folder in " Start \Program\TRENDnet\SecurView". - 58 - 5. 2 1. USING INSTALLATION To launch the program, click Start > Program > TRENDnet > SecurView, and then click SecruViewTM. The main screen will appear as below. NOTE Please set the resolution to 1024x768 or above on your computer while using SecurViewTM; otherwise, the displayed main screen may be distorted. Item features The following describes the function of each item on the main screen: CONTROLS Panel - 59 - - SETTING: Click to enter the Setting screen of SecurViewTM. - PLAY: Click to play the recorded video file using the media player on the computer (for example, Windows Media Player by default). - LOCK: Click to lock the camera controls. If you have set ID and Password in SETTING > Account, you will be asked to enter the required information to unlock. - ALL RECORD: Click to start recording video clips using ALL connected cameras. To stop recording, please click Record button to stop the individual camera. [. . . ] Transceivers can also be used to join a segment that uses one medium to a segment that uses a different medium. On a 10BASE-5 network, the transceiver connects the network adapter or other network device to the medium. Transceivers also can be used on 10BASE-2 or 10BASE-T networks to attach devices with AUI ports. Transceiver U - 91 - UDP User Name Utility UTP The User Datagram Protocol is a connectionless protocol that resides above IP in the TCP/IP suite The USERNAME is the unique name assigned to each person who has access to the LAN. It consists of several pairs of wires enclosed in an unshielded sheath. W WAN Wide-Area Network. [. . . ]