User manual TRENDNET TV-IP100-N

[. . . ] TABLE OF CONTENTS ABOUT THIS GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 FEATURES AND BENEFITS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 UNPACKING THE PACKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Click Next in the welcome screen. Step 3 Read and accept the License Agreement; then, click Yes. Step 4 68 Choose the destination location. If no specific requirement, leave the default setting and click Next. Step 5 The InstallShield Wizard starts to install the software, and the progress bar indicates the installation is proceeding. 69 Step 6 Click Finish to complete the installation. 70 Getting Started This section describes the User Interface of IPView Pro, with detailed procedures for using the application. To launch IPView Pro, click Start > Programs > IPView Pro > IPView Pro. The main screen will appear as below: NOTE: IPView Pro requires the system's resolution setting up to 1024x768. Please configure the resolution to 1024x768 or higher; otherwise, it may shows incomplete screen when launching the program. 71 Item Feature NO. 1 2 Item Date/Time Status Mode Window Description Show current date/time. Click the Change Status Mode button ( ) on the right lower corner of the window to change the display mode: Camera list mode 3 4 5 6 7 8 9 View Window Connect/ Disconnect Rotate image angle Snapshot Camera information mode Show the camera's view in this window. Show four cameras in View Window. Audio ON/OFF Click to turn on/off the camera's audio. Zoom Mode View Mode Buttons 72 Show six cameras in View Window with the first one as the major view. Show eight cameras in View Window with the first one as the major view. Show ten cameras in View Window with the first two as the major views. Show thirteen cameras in View Window with the first one as the major view. Click to exit or minimize IPView Pro. 12 Record Button Record video clip of the selected camera and save it in the computer. When you click the button, you can select Manual Record, Schedule Record, or Motion Record. 13 Play Button Play the recorded video file in the computer. Click to enter the System Configuration. 14 System Configuration 73 Using IPView Pro Adding a Camera To add a camera: 1. Click the System Configuration button to enter the System Configuration. If you are not sure of the camera's IP address, you can click Search to search the available camera(s) within the network. 74 2. Select the camera you want by highlighting it, and then click Add Camera. The camera is added. Click the Add Camera button. The camera found within the network. 3. Click Save, and then click the System Configuration button to return to View Window. You can click Save as to save the selected cameras into the desired path and the selected cameras can be reloaded by load button. 75 Alternately, you can add a camera by entering the its IP address directly: 4. Click the Add Camera button. Enter the camera's IP address and Port. 5. Enter the camera's IP address (default: 192. 168. 10. 30) and Port (default: 80), and then click Add Camera. [. . . ] Transceivers can also be used to join a segment that uses one medium to a segment that uses a different medium. On a 10BASE-5 network, the transceiver connects the network adapter or other network device to the medium. Transceivers also can be used on 10BASE-2 or 10BASE-T networks to attach devices with AUI ports. Transceiver U UDP The User Datagram Protocol is a connectionless protocol that resides above IP in the TCP/IP suite 122 ULP The upper-layer protocol refers to Application Layer protocols such as FTP, SNMP, and SMTP. The USERNAME is the unique name assigned to each person who has access to the LAN. [. . . ]