User manual TRENDNET TU2-ET100

[. . . ] 9 Windows 98SE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Verifying the Driver Installation in Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Mac 10. 6x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Mac 10. 5x. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert the provided CD into your CD-ROM drive, then Click Cancel. 2. Upon your USB device connection, Windows will detect the new device and pop up the following screen. Select Specify a location and click Browse to navigate to x:\Driver\Win98_ME where x: is your CD-ROM drive letter. In the drop-down list, select x:\Driver\Win98_ME and click OK. 13 9. Connect a RJ-45 cable from the TU2-ET100 to a Switch, Router or Cable/DSL Modem. Verifying the Driver Installation in Windows To verify your Ethernet adapter installation, select Control Panel > System > (Hardware) > Device Manager. In the Network adapters group, ASIX AX88772 USB2. 0 to Fast Ethernet Adapter should be displayed. If there is a question or exclamation mark next to that item, then the driver is not properly installed. Please delete the item and repeat the installation steps. *The example screenshot is under Windows XP. 15 Mac 10. 6x 1. There system will pop up a message "A new network interface has been detected" 2. If the message not pop up , please Start System Preferences and select Network, then click the "" to add an "USB Ethernet " service . 3. Select "USB Gigabit Ethernet " then click "Advanced" to setting the network by static IP or thru DHCP way. 16 3. by " Using DHCP" Mode , please Click" Renew DHCP License "to get the IP address , Else you have to enter the related information from your network service provider . 17 4. You will find that a new Ethernet network interface is available 5. Once you finish the installation, you can open GO > Utilities > System Profile > Hardward > USB > to verify if your Ethernet adapter is properly installed. 18 Mac 10. 5x 1. Insert the provided driver CD into your CD-ROM drive. Double-click the CD and navigate to the directory of \Driver\Mac10. x. 2. In the directory of Mac10. x, please double-click AX88772_10. 5 to execute the installer program. 3. The onscreen prompted and please click on Continue to go to next step. 19 4. Please Click on Install to continue this installation. 5. Make sure that you want to install this driver now and the computer will be restarted once the installation is done. Please click on Continue Installation to continue this installation. 20 6. Click on Restart to take the new settings effect. 21 Mac 10. 4. x 1. Copy the archive file under the directory of \Driver\Mac10. 4\ to the desktop and then double-click the file until you locate the setup file. Select a destination disk to install the driver and click Continue. 22 5. When the Authenticate screen appears, enter your password in the provided field and click OK. 7. When the software was successfully installed, click Restart. 23 9. After the restart, plug the Ethernet adapter's USB cable into an available USB port on your computer. Then attach one end of an Ethernet cable to the Ethernet port on the adapter and the other end to your network switch, hub or router. Mac system will detect the new hardware and show the name of the adapter, e. g. [. . . ] TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. [. . . ]