User manual TRENDNET TPL-310AP

[. . . ] Safety Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] To decide the format, select Passphrase or Hex in WPA / WPA2 Cipher Suite Pre-Shared Key Format the drop list. Pre-Shared Key Enter the Pre-shared Key according to the preshared key format you select. This field must be filled with character longer than 8 and less than 64 lengths. (The default value is 1234567890ab) * Please click on the Apply Changes button or the Reset button to save/reset the configuration. 3. 4. 7 Access Control To restrict the clients of Access authentication of wireless clients by MAC address, set up the access list in this page. If the Wireless Access Control Mode is set to "Allow Listed", only the wireless LAN clients whose MAC addresses are listed in the Current Access Control List will be able to connect to the wireless access point and all other clients not listed will be denied access. If the mode is set to "Deny Listed", the wireless LAN clients whose MAC addresses are listed in the Current Access Control List will not be able to connect to the wireless access point and all other clients will be allowed access. This feature is only available when using AP, AP+WDS, or AP+Mesh modes located under Wireless > Basic Clicking "Delete Selected" will delete the checked entries in the list. Clicking "Delete All" will delete all of the entries listed. Items Information Click on the drop list to choose the access control mode. You may select "Allow listed" to allow those allowed MAC addresses or select "Deny Listed" to ban those MAC addresses from accessing to this device or select "Disable". Fill in the MAC address that you wish to control, and give a definition to it. (MAC Address Format: xxxxxxxxxxxx) Lists the MAC Access Control Settings you have added before. To Delete the station on the list, mark the check box in the select item and click the "Delete Selected". If you want to delete all Wireless Access Control Mode MAC Address & Comment Current Access Control list stations on the list, click "Delete All" to remove all of them. * Please click on the Apply Changes button or the Reset button to save/reset the configuration. 3. 4. 8 WDS Settings Wireless Distribution System (WDS) mode uses wireless media to connect to other wireless access points. Another term for this feature is wireless point to point or point to multi-point bridging. Wireless access points using WDS mode must be configured to use the same channel number, wireless security type, and wireless security key. Add other WDS enabled wireless access points using their device MAC addresses. This feature is only available when using WDS, AP+WDS, Mesh, or AP+Mesh modes located under Wireless > Basic Settings. To use WDS, you will require at least 2 or more wireless access points that support WDS. Note: WDS is not a wireless standard and connectivity may or may not be established between different wireless access point devices that support this feature. It is recommended to use the same device model when using this feature. Items MAC Address & Comment Information Fill in the MAC address that you wish to control, and give a definition to it. (MAC Address Format: xxxxxxxxxxxx) Data Rate The transmit limitation of data packets of this wireless AP. [. . . ] Move the phone's base station as far away as possible from your wireless devices. If you are still experiencing low or no signal consider repositioning the wireless devices or installing additional access points. The use of higher gain antennas may also provide the necessary coverage depending on the environment. Chapter 7: Specifications Hardware Standards Interface Powerline Frequency Modulation Protocols Wired Speed Utility OS Compatibility Nodes IEEE 802. 3, IEEE 802. 3x, IEEE 802. 3u, IEEE 802. 11n, IEEE 802. 11b, IEEE 802. 11g, IEEE 802. 11s, IEEE 802. 1d, HomePlug® AV 1 x 10/100Mbps Auto-MDIX RJ-45 Port, Power prong 2 ~ 28 MHz OFDM Symbol Modulation on link synchronization, 1024/256/64/8 - QAM, QPSK, BPSK, ROBO Carrier TDMA and , CSMA/CA Powerline: Up to 200Mbps** Ethernet: Up to 200Mbps (Full Duplex mode) Windows 7 (32/64-bit), Vista (32/64-bit), XP(32/64-bit) Up to 64 (max. ) Recommended: Up to 16* per powerline network Overlapping Powerline Net- Up to 4 (per electrical system) works Powerline Coverage Powerline Security LED Up to 300m (984ft. ) 128-bit AES (Advanced Encryption Standard) Power (PWR), Ethernet Link/Act (ETH), Wireless (WLAN) Powerline (PL) with Connection Quality Indication Power Switch Buttons Dimension (L x W X H) Weight Power Source Consumption Temperature Humidity Certifications Best (Green) Better(Amber) Good (Red) On/Off power switch Sync, WPS, Reset A: 103 x 81 x 66 mm (4. 1 x 3. 2 x 2. 6 in. ) EU: 103 x 81 x 81 mm (4. 1 x 3. 2 x 3. 2 in. ) A: 266 g (9. 4 oz) EU: 272 g (9. 6 oz) A: 100~230V AC, 50~60Hz EU: 220~240V/ 5A AC, 50Hz 8. 4 Watts (max. ) Operating: 0° ~ 40°C (32° ~ 104°F) Storage: -10° ~ 70°C (14° ~ 158°F) Max. 90% (non-condensing) CE, FCC Wireless Modulation Access Point Modes OFDM with BPSK, QPSK, 16QAM, and 64QAM Access Point (AP) Access Point (AP) Client (wireless adapter) Wireless Distribution System (WDS) Wireless Distribution System (WDS) with Access Point (AP) Mesh Mesh with Access Point (AP) Repeater (using AP mode only) Frequency Band Data Rate*** 2. 412GHz ~ 2. 472GHz 802. 11b: 1, 2, 5. 5, and 11Mbps 802. 11g: 6, 9, 12, 18, 24, 36, 48 and 54Mbps 802. 11n: up to 300 Mbps Security Antenna Channel Output Power 64/128-Bit WEP (HEX & ASCII), WPA/WPA2 RADIUS, WPA/WPA2PSK 2 x 2dBi internal printed dipole antennas 2. 4GHz: 1~11 (FCC), 1~13 (ETSI) 16dBm typically @ 802. 11b 14dBm typically @ 802. 11g 13dBm typically @ 802. 11n Receiver Sensitivity 802. 11n Typical -68 dBm 802. 11g Typical -73 dBm 802. 11b Typical -84 dBm * Maximum of 16 adapters (nodes) recommended for streaming video across your network. [. . . ]