User manual TRENDNET TPE-224WS

[. . . ] FCC Warning This equipment has been tested and found to comply with the regulations for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. If not installed and used in accordance with instructions in this User's Guide, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at user's expense. CE Mark Warning This is a Class A product. [. . . ] Delete Item: To delete the device in the Monitor List. Device Setting Configuration Setting: Under Configuration Setting, you can set the IP Address, Subnet Mask, Gateway, Set Trap to (Trap IP Address), System name, Location and DHCP function. Select the device in the Discovery list or Monitor List and click Configure Settings. After making the desired changes, enter the password and click "Set". Configuration Setting Password Change: This option allows you to change the password, Enter the original password, the new password, confirm the new password and click "Set". 22 Figure 10. Password Change Firmware Upgrade: When the device has a new function, there will be a new firmware to update the device, use this function to update. Select the path of where the firmware updated firmware is located by clicking "Browse". Once you have selected the firmware, type the password of the device Figure 11. Firmware Upgrade Web Configuration: Double click the device in the Monitor List or select a device in the Monitor List and click "Access Web" to access the Switch's browser configuration. DHCP Refresh: Click "DHCP Refresh" to refresh the IP address of selected device form DHCP server. Toolbar The toolbar in the utility has menu options; File, View, Options and Help. 23 There are four options under "File"; Monitor Save, Monitor Save As, Monitor Load and Exit. Monitor Save: To record the setting of the Monitor List to the default. The next time you open the utility, it will auto load the default recorded setting. Monitor Save As: To record the setting of the Monitor List with a specific filename and file path. There are four options under "View"; view log and clear log function. This option allows the user to set the time for monitoring the device. There is one option under "Help"; About, About displays the version of the utility. 24 Configuring the Switch The TPE-224WS 28-Port 10/100/1000Mbps Gigabit Ethernet Web Smart PoE Switch has a Web GUI interface for smart switch configuration. A network administrator can manage, control and monitor the switch from the local LAN. This section indicates how to configure the Switch to enable its smart functions Login Before you configure this device, make sure your computer is on the same subnet as the Web Smart PoE Switch. For example, since the default IP address of the Web Smart PoE Switch is 192. 168. 0. 1, then the computer should be set at 192. 168. 0. x (where x is a number between 2 and 253), and the default subnet mask is set to 255. 255. 255. 0. Enter IP address http://192. 168. 0. 1 (the factory default IP address setting) into the address bar. 25 You can also access the browser configuration through the utility program. Select the device shown in the Monitor List and then click "Web Configuration". When the login screen appears, enter the default password "admin" and click Login. After entering the password, the page below appears; this screen displays the device status. 26 Setup Setting The following seven links appear under Configuration Setting: Port Setting, IEEE 802. 1Q VLAN Settings, Trunk Setting, Mirror Setting, IEEE 802. 1p Default Priority, PoE Port Setting, PoE System Setting and Broadcast Strom Control Setting in Setup menu. PoE Port Setting When you click on PoE Port Setting, the PoE Status will appear on the screen. [. . . ] All of the configuration will be reset, the IP address of the device will be set to default setting 192. 168. 0. 1. Figure 40. Factory Reset Backup Setting The backup setting help you to backup the current setting of the Switch. Once you need to backup the setting, press the "Backup" button to save the setting. To restore a current setting file to the device, you must specify the backup file and press "Restore" button to proceed the setting of the recorded file. Figure 41. [. . . ]