User manual TRENDNET TFM-560U

[. . . ] E500 V. 90 USB MODEM USER'S MANUAL 38 Lo ok E500 V. 90 USB MODEM USER'S MANUAL TABLE OF CONTENT 1. Comprehensive Modem Installation Instructions 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Setup Instructions for Windows 98. . . . . . . . . . . 3 Testing your modem. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Monitor Application of USB modem. . . . . . . . . . . . . 7 Install Communication Software. . . . . . . . . . . . . . . 9 3. Troubleshooting Appendix 1: Modem Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Appendix 2: ModioTM AT Command Sets. . . . . . . . . . . . . . . . . . . . . . 12 Appendix 3: Government Compliance notices. . . . . . . . . . . . . . . . 37 P. 1 E500 V. 90 USB MODEM USER'S MANUAL 38 Section 1 Contents of Package - One V. 90 USB Modem - Quick installation guide - One CD-ROM disk comprises Communication software, Modem Driver & User's Manual - One Telephone Cable - One USB Cable Please contact the place of purchase if any of the above listed items are missing. Section 2 Section 2. 1 Comprehensive Modem Installation Instructions System Requirements The modem operates on a personal computer equipped with the following: - Pentium R 166MMX or faster CPU ( 200 MHz recommended ) - 16 MB RAM - USB port - Windows 98 or Windows NT 5. 0 operating system Section 2. 2 Hardware Installation Please refer to Fig. 2 - 1 and proceed to following steps for how to connect your modem to the computer and with USB port and telephone wire. Phone Jack FIGURE 2-1 V. 90 USB modem diagram USB Jack 1. [. . . ] If the modem has finished dialing, It proceeds as if +FRH=3 command has been issued. It will decide (based on timers) when the other side answers in voice and a voice session will take place. Related S-Reg: S5, S6, S7, S16, S22, S28, S56 En Set local echo The modem enables/disables echo of characters to DTE. Enable command echo. (default) n=0 or 1 Otherwise (space) String format characters - ignored any other character - ignored. Result codes: Related S-Reg: S13 Set ON/OFF hook H0 H1 OK Error Modem hangs up (goes on-hook). n=0 or 1 Otherwise Result codes: In Identification/Information I1 I2 Modem Name, Vendor Name, Modem Version, for example : ModemX , ModemWorks Ltd. 1. 23 P. 14 E500 V. 90 USB MODEM USER'S MANUAL 38 I3 Chipset Vendor/Chipset ID, for example ST Microelectronics XY4220 I4 Modem active profile for example, Active Profile: S00=000 S01=000 S02=000 S03=000 S04=000 S05=000 S06=000 S07=000 S08=000 S00=009 S10=000 S11=000 S12=000 S13=000 S14=000 S15=000 S16=000 S17=000 S18=000 S01=019 S20=000 S21=000 S22=000 S23=000 S24=000 S25=000 S26=000 S27=000 S28=000 S29=000 S30=000 S31=000 S32=000 S33=000 S34=000 S35=000 S36=000 S37=000 S38=000 S39=000 S40=000 S41=000 S42=000 S43=000 S44=000 S45=000 S46=000 S47=000 I5 Stored profile 0 Active Profile 0: (Same format as above) I6 Stored profile 1 Active Profile 1: (Same format as above) I7 Display stored pone numbers (See &Z command) Ln Speaker volume Select speaker volume. L0 L1 L2 L3 OK Error Low Low (Default) Medium High n=0-3 Otherwise Result codes: Related S-Reg: S30 Mn Speaker control Select when the speaker is On/Off. M0 M1 M2 M3 Speaker always OFF Speaker ON from start of dialing until receiving carrier (Default) Speaker always ON Speaker OFF from end of dialing until receiving carrier P. 15 E500 V. 90 USB MODEM USER'S MANUAL 38 Result codes: OK Error n=0-3 Otherwise Related S-Reg: S29 Nn Automode control Enable/Disable Automode detection. A subsequent handshake will be conducted according to the contents of S32. A subsequent handshake will be conducted according to the Automode algorithm. (Default) n=0 or 1 Otherwise Result codes: OK Error Related S-Reg: S31 On Returns to on-line data mode This command is normally used to connect the DTE back after an escape (+++) has been issued. n=0-1 Otherwise Result codes: P Pulse dialing Forces pulse dialing. This command holds until the next T dial modifier or T command is received. Upon successful completion of handshake, the modem will go on-line in answer mode. Related S-Reg: S16 Q Quiet result codes control Q0 Q1 OK Error Enable sending result codes to DTE. (Default) Disable sending result codes to DTE. n=0 or 1 Otherwise Result codes: Related S-Reg: S14 P. 16 E500 V. 90 USB MODEM USER'S MANUAL 38 S Read/Write S-Register This command has a few derivatives: Sn=v Sn?Sets the value v (decimal) to S-register n (v=0-255) Displays the value of S-register in decimal format (3 digits) Note: Some registers are read-only Result codes: OK Error All parameters valid Invalid S register or value. Trying to write to a read-only register T Tone dialing Forces tone dialing. This command holds until the next T dial modifier or T command is received. Related S-Reg: S16 Vn Verbose/Numeric result codes Select the time of result messages sent to the DTE. Long form (verbose) result codes to be sent to DTE. (Default) n=0 or 1 otherwise Result codes: Related S-Reg: S15 Xn Extended result codes Select the subset of result codes to be used by the modem to the DTE. If the modem is in fax mode (+FCLASS=1), the only message sent to indicate connection is "CONNECT" without a speed indication. [. . . ] Registers denoted with a * may be customized using the PTT Wizard Tool. Factory defaults Factory defaults are stored in the Windows OS registry. In addition the designated default profile (as specified by the Yn command) is subsequently loaded. The defaults shown are of the Smart Link factory settings 0 and 1. S-Register Summary Note: This S-register List is not to be used as is by End Users and in End User's manuals. For end users the contents of the first 24 S-registers should suffice. P. 35 P. 36 38 E500 V. 90 USB MODEM USER'S MANUAL E500 V. 90 USB MODEM USER'S MANUAL 38 Appendix3 FCC compliance Government compliance notices This equipment complies with Part 68 of the FCC Rules. [. . . ]