User manual TRENDNET TEW-P1U1P

[. . . ] Table of Contents Chapter 1 Introduction 1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Example (Unix): arp -s 192. 168. 0. 21 00:c0:02:12:34:56 Example (Windows): arp -s 192. 168. 0. 21 00-c0-02-12-34-56 Note: The hardware address of the Wireless Print Server is shown on a sticker on the base of the device. Page 39 Connecting to the Wireless Print Server 1. In the Address box, enter HTTP:// followed by the IP Address of the Wireless Print Server. Remember to save each screen before changing to a different screen. 3. 4. Configuration Screens Depending on your model and Firmware version, the Web-based interface may look different to the images shown in this User's Manual. The functions have not changed, and the description of each setting is correct. Only the appearances are different. AppleTalk Figure 32: AppleTalk Screen AppleTalk zone Printer Object Type Communication Protocol This determines which Apple systems can gain access to this printer. These are text fields, used to describe the printer driver used for each port. The Wireless Print Server is designed to work with LaserWriter (or 100% compatible) printers. The default is Binary. Page 40 NetBEUI Figure 33: NetBEUI Screen Domain Name Enter the designated work group to be serviced by the Wireless Print Server. This field is not case sensitive, so names with different case will be considered to be the same name. The default value of zero (0) delay should be increased only if your printer cannot cope with no delays. If print errors occur, try setting this value to YES. Response Time Abort Job if Error Page 41 TCP/IP Figure 34: TCP/IP Screen IP Address Subnet Mask (Network Mask) Gateway Address Connection Delay before reconnection attempts Number of reconnection attempts IP Address assigned to this device. If using dynamic IP Addresses (DHCP, BOOTP, rarp), this should be left at 0. 0. 0. 0. If the Router (Gateway) Address is 0. 0. 0. 0, the Subnet Mask should also be left at 0. 0. 0. 0. If you have a router, enter the Subnet mask for the segment to which the Wireless Print Server is attached. If your network segment has a router or gateways, enter its IP Address here. Sets how long the Wireless Print Server should wait before retrying a TCP/IP connection which is lost. Allowable values are from 0 to 255, with 254 as the default. Page 42 Configure Server Figure 35: Configure Server Screen Print Server Name Password Change the default name if you wish. Once a password is entered, it is required in order to gain access and change the configuration. The available protocols depend on the Print Server model. Enable Protocols Page 43 Wireless Configuration The settings on this screen must match the other Wireless stations in order for communication to occur. Figure 36: Wireless Screen Page 44 Configuration Regulatory Domain Station name It is illegal to use this device in any location outside of the regulatory domain. On your PC, some Wireless status screens may display this name as the Access Point in use. If you experience lost connections and/or slow data transfers you may need to experiment with different channels to see which is the best. [. . . ] Example: lpr -P Marketing /etc/hosts In the above example, the /etc/hosts file is sent to the printer queue Marketing. It will then be sent to the logical printer associated with this queue. Page 73 Netware Systems Overview · · The Print Server must be configured as a valid device on your TCP/IP network. To use NDPS (Novell Distributed Printing Services), the Novell server must be running Novell NetWare 5, and the PCs (clients) must be running IntranetWare Client V2. 2. or later. The following procedure is designed to enable Public Access Printing under NDPS. [. . . ]