User manual TRENDNET TEW-P1PG

[. . . ] TABLE OF CONTENTS ABOUT THIS GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PACKAGE CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 SYSTEM REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It also allows you to select the PJL Printer setting (Yes or No). NOTE: PJL (Print Job Language) has certain job requirements that must be met to work correctly. For more information, please refer to your printer's manual. - 31 - Configuration Wireless Wireless Interface Connection Mode: Select one of the three connection modes. · Infrastructure (default) - Connects to compatibly configured wireless AP or router in a WLAN. - 32 - - - Ad-Hoc - Connect to compatibly configured wireless clients in the peer-to-peer mode. You can manually input the name or select one from the pull-down menu. To search the available wireless AP within the network, click the Site Survey button. Transmission Rate: Select the data transmit rate from the pulldown menu. The default setting is Fully Automatic. · WEP Encryption This field allows you to configure the settings of data encryption. Please remember that the WEP key must be set before the data encryption is enforced. WEP Encryption: This option allows you to select Disable, 64 bits, and 128 bits for the encryption setting. WEP Key Format: You can decide the network key to be encoded by ASCII (ASCII characters) or HEX (hexadecimal digitals). Then, enter the key(s) for the network in the Key box (1~4). - 33 - Advanced Setting This field allows you to configure more settings, including: - Beacon Interval: Enter the number of beacon interval time in millisecond. Setting options are: Long - it is set to 144 bits; Short - it is set to 72 bits. - Authentication Type: You can set the authentication type by selecting the settings: Open System, Shared Key, and Both. TIP: Once you have changed the settings in each option, click Save to store the settings, or Cancel to abandon. - 34 - Configuration Network TCP/IP This field contains three options that allow you to configure the TCP/IP setting: IP Address, UPnP, and MAC Rendezvous. - 35 - - - - IP Address: This option allows you to set the IP address manually or automatically. When you choose Manually Assign, you should enter the related information in the following boxes, including IP Address, Subnet Mask, and Default Gateway. DNS Server Address: DNS (Domain Name System) server is an Internet service that translates domain names into IP addresses. MAC Rendezvous: This option allows you to enable or disable MAC Rendezvous mode. Second HTTP Port: The default port for communication is via port 80, and you can change it according to your network configuration. Select Enable from the option and enter the desired port number in the following box. Microsoft Network Enter the name of the Workgroup that you want the print server associated with in this field. - 36 - AppleTalk Enter the AppleTalk Zone name in the box. In the following options, enter the related configuration, such as the printer type. · PostScript Level: Select from the pull-down menu (Level 1 or Level 2). · Font Group: Select from the pull-down menu. TIP: Once you have changed the settings in each option, click Save to store the settings, or Cancel to abandon. - 37 - Configuration User Printing Control By configuring the Enable User Printing Control option (Yes or No), the user in the User List is permitted to access the print server or not. For the user(s) who is not in the User List, you can also limit the access right by setting the Allow Undefined Users Printing option to Yes or No. - 38 - Define Users You can add/delete the user(s) to/from the User List. The User List at the bottom of the screen displays the current defined user and related information for the print server. TIP: Once you have changed the settings in each option, click Save to store the settings, or Cancel to abandon. - 39 - Configuration E-mail E-mail Account You can assign an E-mail address to the print server, so that your mail of the account can be printed out directly through the printer (ASCII text only). [. . . ] Please confirm that the AppleTalk protocol is enabled in your Macintosh computer. Change the IP Address on one of the computers within your network to 192. 168. 0. x (where x is any number between 2-254). Type 192. 168. 0. 1 (the default IP Address) into the address field of your browser. If your AppleTalk network is divided into AppleTalk zones, you have to specify which zone the Print Server should be in. [. . . ]