User manual TRENDNET TEW-MFP1

[. . . ] TRENDnet User's Guide Cover Page TRENDnet User's Guide Table of Contents Change Admin Account Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Change User Account Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Contents Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Click on the Wireless tab and scroll down to the Site Survey Setting section. Press the Apply button to start scanning for available wireless networks. Change Wireless settings Wireless You can change the wireless settings of the device and connect to another wireless network. Any changes applied to these settings must match your wireless network. Log into your router management page (see "Access your router management page" on page 13). 3. 4. Select your wireless network and click Set button 3. Select the Network Type you would like set on the device. 6. The selected wireless network will automatically be entered in the SSID field. If you cannot see your wireless network click on Scan AP to refresh the list. © Copyright 2012 TRENDnet. 14 TRENDnet User's Guide Wireless Security settings Wireless Similar to the previous section, you can change the wireless security settings of the device when changes were made on your wireless network. WEP is the only security type that can be used when the device is set to Ad-Hoc Network Type. Any changes applied to these settings must match your wireless network. Log into your router management page (see "Access your router management page" on page 13). Select the wireless security/encryption type applied on your wireless network under Security System. TEW-MFP1 5. WPA-PSK or WPA2-PSK o Key Format: Select the format type o Pre-Shared Key: Enter the key or password o Encryption: Selected encryption type set on your wireless network Click Apply. · WPS Setting General Wi-Fi Protected Setup or WPS is a feature that allows the device to authenticate to your wireless network, the TEW-MFP1 supports WPS Push Button and PIN Configuration. When using WPS make sure your wireless router or access point supports these features. The WPS Push Button Configuration or PBC can be initialized from a virtual button following the steps below or from a physical button located on the side of the unit. Please refer to Product Hardware Features section for more information. Log into your router management page (see "Access your router management page" on page 13). Select Enable and click on Apply 4. Enter your wireless network's encryption information. · WEP o Authentication: Select the authentication type o Key Size: Authentication Key Size o Key: Selected and enter key set on your wireless network 4. Select the type of WPS Mode you would like to use. © Copyright 2012 TRENDnet. 15 TRENDnet User's Guide · PBC o o o Mode: Select PBC Click Trigger to initialize WPS Initiate WPS Push Button on your wireless router or access point TEW-MFP1 3. Click Apply to save settings. Change Device Information · PIN o o o o o o o General In most cases, you do not need to change the device information and the default settings are just fine. These settings help you determine or find the device from features like Windows Network Map or a router's client list. · Server Name: The device name described on your network · Workgroup: The work group assigned to the device · Description: The product descript of the device 1. Log into your router management page (see "Access your router management page" on page 13). [. . . ] If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. Do not remove or attempt to service the product by any unauthorized service center. [. . . ]