User manual TRENDNET TEW-736RE

[. . . ] TRENDnet User's Guide Table of Contents © Copyright 2011 TRENDnet. All Rights Reserved. 1 TRENDnet User's Guide Table of Contents Contents Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Log into to the management page (see "How to access the management" page 9). Click Rescan if you do not see your wireless network. Change the IP address Network > LAN Setting TRENDnet recommends setting the TEW-736RE to DHCP Mode which allows the TEW736RE to automatically obtain an IP address from your wireless router, or access point. However the IP address you assign must be within the same subnet of your network. Any network device outside the subnet will not be able to communicate within the network. Note: You can assign an IP address outside of the DHCP server's range or assign an IP address towards the last IP possibly assigned from the DHCP server. Log into to the management page (see "How to access the management" page9). If wireless device for which you are connecting has security enabled you will be prompted to enter the device's wireless password in the Pre-Share Key field. 3. All Rights Reserved. TRENDnet User's Guide TEW-736RE Saved configuration settings can be used and uploaded to the device. Once the configuration file is uploaded the device will automatically be configured based on the saved settings. Log into the management page (see "How to access your router management page" on page 9). Click on Administrator and Settings Management. 6. Enter the wireless passwordand click Apply. 3. Click Import to upload the settings. Save configured settings Administrator >Settings Management Applied settings on the device can be saved and can be use to restore settings. The device will automatically be configured based on the saved settings. This can be used to immediately restore settings to the device of when configuring multiple devices. Log into the management page (see "How to access your router management page" on page 9). Click on Administrator and Settings Management. Reboot your device Administrator > Settings Management There may come a time when the TEW-736RE needs a power cycle or reboot. Instead of unplugging the power adapter and plugging it back on, you can follow the steps below to reboot the device. Log into the management page (see "How to access your router management page" on page 9). Name the file name you would like and select the location for which you would like to save the file. 3. Click on Reboot button. Load saved settings Administrator > Settings Management © Copyright 2011 TRENDnet. All Rights Reserved. 12 TRENDnet User's Guide Reset your device to factory default Administrator > Settings Management There are two ways you can restore or reset the device back to factory default settings. Press and hold the reset button on the side of the unit for 10 seconds and release (see side "Side Panel "on page 3). You can also follow the steps below to reset the device through the user interface. [. . . ] TEW-736RE ­ 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. [. . . ]