User manual TRENDNET TEW-715APO

[. . . ] TRENDnet User’s Guide Cover Page TRENDnet User’s Guide Table of Contents How to choose the type of security for your wireless network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Secure your wireless network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Wireless access control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Contents Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] • Wireless Network Name (SSID): This acronym stands for Service Set Identifier and is the name of your wireless network. You can manually enter the wireless network you want to connect to or click “Site Survey” option to scan for available wireless networks around you. Please refer to pagexxx • Lock AP MAC: Enter the MAC address of the access point you are connected. All Rights Reserved. 24 TRENDnet User’s Guide some cases, however, like where there is no great demand for speed, you can have a relatively-low transmit rate for compromise of a long distance. • Extension Channel Protection: This is to avoid conflict with other wireless network and boost the ability of your device to catch all 802. 11g transmissions. Compared to CTS-Self; the transmission amount of CTS-RTS is much lower. • Enable MAC Clone: Available only under wireless client mode, it hides the MAC address of the AP while displays the one of associated wireless client or the MAC address designated manually. Site Survey: The following section outlines how to utilize the site survey option in Wireless Client mode. Log into the management page (see “Access the management page” on page 9). Select Wireless Client in the Operation Mode pull down menu and click Apply. Click Apply when you have selected the wireless network you want to connect with. If your wireless network is configured with wireless security, click Profile Settings 5. Select the access point or wireless network you want to connect. o Profile Name: Enter the profile name you would like to assign to the wireless network. • Wireless Network Name (SSID): Name of the wireless network you are connecting too. It allows wireless communication to define a priority limit on the basis of data type under AP mode only, thus those time-sensitive data, like video/audio data, may own a higher priority than common one. To enable WMM, the wireless client should also support it • Security Settings: Select and configure the wireless security of your wireless network. • Select AP: Configures the access point based on the selected AP’s SSID and MAC address • Select SSID: Configures the access point based on the selected AP’s SSID only • Scan: Scans for available wireless networks. © Copyright 2012 TRENDnet. 25 TRENDnet User’s Guide Bridge Mode Wireless > Basic TEW-715APO When Bridge is selected a wireless network is created with your device (similar to a wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port. This section outlines available management options under the Basic Settings of the Wireless button when the Operation Mode is set to Bridge and will assist in setting up the access point. • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). [. . . ] If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit’s warranty continues from the original date of purchase. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. Do not remove or attempt to service the product by any unauthorized service center. [. . . ]