User manual TRENDNET TEW-690AP

[. . . ] Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Note that changes made in this section may also need to be duplicated on wireless clients that you want to connect to your wireless network. To protect your privacy, use the wireless security mode to configure the wireless security features. The Wireless tab provides the following configuration options: Basic, Advanced, MAC Filter, Security, WPS and Station List. ACCESS POINT Page 20 Repeater Mode Support Repeater Mode Support allows you to "repeat" a wireless signal from an existing access point. Select the radio button to enable or disable "Repeater Mode Support". When enabled you have the option of defining the specific access point to repeat off of by entering in the remote access points or wireless router's wireless MAC address into the "Repeater MAC Addr. You must also configure the TEW-690AP with the same SSID, channel and wireless encryption settings of the remote access point. Repeater Mode Support Wireless Mode If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve performance slightly by choosing the appropriate "Only" mode. If you have some devices that use a different transmission mode, choose the appropriate "Mixed" mode. Wireless Modes 802. 11b/g mixed mode (2. 4GHz) - This wireless mode works in the 2. 4GHz frequency range and will allow both wireless b and wireless g client to connect and access the TEW-690AP at 11Mbps for wireless b, at 54Mbps for wireless g and share access at the same time. Although the wireless b/g operates in the 2. 4GHz frequency, it will allow the use of other 2. 4GHz client devices (Wireless n/g @ 54Mbps) to connect and access at the same time. 802. 11n only (2. 4GHz) - This wireless mode works in the 2. 4GHz frequency range and will only allow the use of wireless n client devices to connect and access the TEW-690AP up to 300Mbps*. Although the wireless n operates in the 2. 4GHz frequency, this mode will only permit wireless n client devices to work and will exclude any other wireless mode and devices that are not wireless n only. 802. 11b/g/n mixed mode (2. 4GHz) - This wireless mode works in the 2. 4GHz frequency range and will only allow the use of wireless g client devices to connect and access the TEW-690AP at 11Mbps for wireless b, 54Mbps for wireless g and up to 300Mbps* for wireless n and share Page 21 access at the same time. Although the wireless b/g/n operates in the same 2. 4GHz frequency, it will allow the use of other 2. 4GHz client devices (Wireless b/g/n) to connect and access at the same time. Wireless Name (SSID) When you are browsing for available wireless networks, this is the name that will appear in the list (unless Broadcast Network Name is set to Disable, see below). For security purposes, it is highly recommended to change from the pre-configured network name. Add up to three additional SSIDs to create virtual wireless networks from one wireless Access Point. Multiple SSID # This Access Point support multiple SSID function, you can assign three more SSID for the TEW-690AP. Create virtual SSID wireless networks (WLAN) with different type of wireless security for each virtual WLAN that is created. When using the wireless adapter wireless site survey tool, there will be additional wireless network to connect with once the feature is enabled. Multiple SSID (Virtual WLANs) Add Additional Wireless Network Name (SSID) To add additional Wireless Network Names simply add the name to the Multiple SSID field and click on apply at the bottom of the page. When finished, go to the Security section in this Users Guide for wireless security configuration. Multiple SSIDs Page 22 Broadcast Network Name (SSID) This option allows you to hide your wireless network. When this option is set to enable, your wireless network name is broadcast to anyone within the range of your signal. If you're not using encryption then they could connect to your network. When this mode is disabled, you must enter the Wireless Network Name (SSID) on the client manually to connect to the network. Frequency (Channel) A wireless network uses specific channels in the wireless spectrum to handle communication between clients. [. . . ] TEW-690AP ­ 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. [. . . ]