User manual TRENDNET TEW-659BRV

[. . . ] TRENDnet User's Guide Cover Page TRENDnet User's Guide Table of Contents PPTP (Point-to-Point Tunneling Protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Client-Server VPN (Server Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Client-Server VPN (Client Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 L2TP (Layer 2 Tunneling Protocol) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To configure outbound packet filters: Next to Outbound Packet Filter, check the Enable option to enable outbound filtering. 5. Note: If you would like to discard the changes, click Undo before you click Save. · · Select Allow all to pass except those match the following rules to allow all traffic and deny only the filters specified in the list. Select Deny all to pass except those match the following rules to deny all traffic and allow only the filter specified in the list. © Copyright 2012 TRENDnet. 47 TRENDnet User's Guide Review the outbound packet filter settings. Inbound Packet Filter TEW-659BRV You may want apply inbound packet filters to allow or deny access of specific traffic from the Internet to computers or devices on your local network. To configure inbound packet filters: Click Inbound Filter at the bottom of the outbound packet filter page. · · Source IP ­ Enter the source IP address or computer/device IP address on your local network to apply the filter. 192. 168. 10. 101) Destination IP : Ports ­ Enter the destination IP address of the computer/device located on the Internet and port number to apply the filter. To specify all port numbers, do not specify any value for Ports field. For specific port numbers, enter a port number or range within the range of 1-65535 (e. g. Note: Typically, you can specify 0. 0. 0. 0 for any destination IP address located on the Internet or enter the specific IP address. 10. 10. 10. 200) · · · Protocol ­ Select the protocol type to filter. Use rule# - Click the drop-down list to select a pre-defined schedule. The filter will only be active during the time period defined in the pre-defined schedule. Note: Before applying scheduling, please ensure your Time settings are configured correct and you have defined a schedule. See page 51 to configure Time Settings and see page 65 to create a schedule. Note: If you would like to discard the changes, click Undo before you click Save. Next to Inbound Packet Filter, check the Enable option to enable inbound filtering. · · Select Allow all to pass except those match the following rules to allow all traffic and deny only the filters specified in the list. Select Deny all to pass except those match the following rules to deny all traffic and allow only the filter specified in the list. Clicking MAC Level will bring you to the MAC Control configuration page. See MAC Control section. · Source IP ­ Enter the source IP address or computer/device IP address on your located on the Internet to apply the filter. 192. 168. 10. 101) Note: Typically, you can specify 0. 0. 0. 0 for any source IP address located on the Internet or enter the specific IP address. [. . . ] If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. Do not remove or attempt to service the product by any unauthorized service center. [. . . ]