User manual TRENDNET TEW-412APBO

[. . . ] Upgrade Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction Thank you for purchasing TRENDnet's Wireless 802. 11g Outdoor AP Bridge. The package you have received should contain the following items: For TEW-412APBO TEW-412APBO User's Guide CD-ROM Quick Installation Guide POE Host & Power Cord Mounting Kit Cat. 5 Ethernet Cable (1. 5m/5ft. ) For TEW-413APBO TEW-412APBO User's Guide CD-ROM Quick Installation Guide POE Host & Power Cord N-type Male to N-type Male Cable (2meters) Mounting Kit Cat. 5 Ethernet Cable (1. 5m/5ft. ) Note: if anything is missing, please contact your vendor User's Guide 4 2. [. . . ] The default selection is 300 seconds. * Click Apply to save your settings. User's Guide 11 4. 2. System AP Password: Changing the password for the AP is as easy as typing the password into the Enter New Password field. Use the default password when you first open the configuration pages, after you have configured these settings, you should set a new password for the AP (using the Password screen). This will increase security, protecting the AP from unauthorized changes. Restore Factory Defaults: Click the Yes button to reset all configuration settings to factory default values. Note: Any settings you have saved will be lost when the default settings are restored. Click the Apply button to save the setting. Backup/Restore Setting: Click Backup to store the Access Point's configuration on your local PC. Click Restore to restore Access Point's configuration from your local PC * Check all the settings and click Apply to save them. User's Guide 12 4. 3. Operating Mode Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs to wireless stations. User's Guide 13 Important Both units must be selected as AP Repeater mode in order to establish the Wireless link communication. The remote AP MAC address to be filled at this selection should be the LAN MAC address that is displaying at the Operating Mode's web pages AP Repeater: This mode allows the AP to keep the AP function role and at the same time performing a communication with other 802. 11g AP to establish and extend your Wireless Network cover. Please enter the Remote Access Point's MAC address to enable this feature. Wireless Bridge: This mode allows the connection of one or more remote LANs with a central LAN. * Click Apply to save your settings. User's Guide 14 4. 4. Status This screen displays the IEEE 802. 11g AP's current status and settings. This page will auto re-flash every 5 seconds to keep most update information. LAN section will be displaying all information related on AP, such as the IP address and the current configuration type. Wireless section will be displaying information related on the Wireless interface, such as SSID, Channel, Encryption and statistics of network traffic. *Click the Refresh button to refresh the AP's status and settings. User's Guide 15 4. 5 Traffic Log Traffic Log: The AP can keep logs of all incoming or outgoing traffic for your network traffic. To keep a permanent record of activity logs as a file on your PC's hard drive, Log viewer software must be used. In the Send Log to field, enter the fixed IP address of the PC running the Log viewer software. To see a temporary log of the AP's most recent traffic, click the View Log button. . Click the Apply button to save the setting. User's Guide 16 4. 6 Access Control Access Control: This function will allow administrator to have access control by enter MAC address of client stations. * Click Apply to save your settings. User's Guide 17 4. 7 Advanced Wireless Authentication Type: Auto: Auto is the default authentication algorithm. It will change its authentication type automatically to fulfill client's requirement. Open System: Open System authentication is not required to be successful while a client may decline to authenticate with any particular other client. Shared Key: Shared Key is only available if the WEP option is implemented. Shared Key authentication supports authentication of clients as either a member of those who know a shared secret key or a member of those who do not. [. . . ] WARRANTIES EXCLUSIVE: IF THE TRENDWARE PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDWARE'S OPTION, REPAIR OR REPLACEMENT. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDWARE NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDWARE'S PRODUCTS. TRENDWARE SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. [. . . ]