User manual TRENDNET TEW-410APBPLUS

[. . . ] Upgrade Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction Thank you for purchasing TEW-410APBplus 54Mbps 802. 11g Wireless Access Point This user guide will assist you with the installation procedure. The package you have received should contain the following items: TEW-410APBplus User Guide (CD-ROM) Quick Installation Guide DC Power Adapter and Power cord One Cat5 Cable Note: if anything is missing, please contact your vendor User's Guide 3 2. [. . . ] TKIP utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. AES stands for Advanced Encryption System, which utilizes a symmetric 128-Bit block data encryption. To use WPA Pre-Shared Key, enter a password in the WPA Shared Key field between 8 and 63 characters long. You may also enter a Group Key Renewal Interval time between 0 and 99, 999 seconds. WPA Algorithms WPA Shared Key Group Key Renewal Please choose your algorithms method. The default selection is 300 seconds. User's Guide 9 -WPA RADIUS WPA RADIUS uses an external RADIUS server to perform user authentication. To use WPA RADIUS, enter the IP address of the RADIUS server, the RADIUS Port (default is 1812) and the shared secret from the RADIUS server. WPA Algorithms Radius Server Address RADIUS Server Port RADIUS Shared Key Group Key Renewal Please choose your algorithms method. Please input your RADIUS Server IP address. Please input the Authentication port of your RADIUS server. The default port being used is 1812 The RADIUS server will accept the authentication if both Shared Key matched. The default selection is 300 seconds. * Click Apply to save your settings. TEW-410APBplus 4. 2. System AP Password: Changing the password for the AP is as easy as typing the password into the Enter New Password field. Use the default password when you first open the configuration pages, after you have configured these settings, you should set a new password for the AP (using the Password screen). This will increase security, protecting the AP from unauthorized changes. Restore Factory Defaults: Click the Yes button to reset all configuration settings to factory default values. Note: Any settings you have saved will be lost when the default settings are restored. Click the Apply button to save the setting. Backup/Restore Setting: Click Backup to store the Access Point's configuration on your local PC. Click Restore to restore Access Point's configuration from your local PC * Check all the settings and click Apply to save them. User's Guide 11 4. 3. Operating Mode Access Point: This mode provides access for wireless stations to wired LANs and from wired LANs to wireless stations. In this operating mode, the device will be used as wireless NIC. TEW-410APBplus Important Both units must be selected as AP Repeater mode in order to establish the Wireless link communication. The remote AP MAC address to be filled at this selection should be the MAC address that is displaying at the Operating Mode's web pages AP Repeater: This mode allows the AP to keep the AP function role and at the same time performing a communication with other 802. 11g AP to establish and extend your Wireless Network cover. Please enter the Remote Access Point's MAC address to enable this feature. Wireless Bridge: This mode allows the connection of one or more remote LANs with a central LAN. * Click Apply to save your settings. User's Guide 13 4. 4. Status This screen displays the IEEE 802. 11g AP's current status and settings. This page will auto re-flash every 5 seconds to keep most update information. LAN section will be displaying all information related on AP, such as the IP address and the current configuration type. [. . . ] For example, if the AP is set to 192. 168. 1. 250, change the IP address of your computer to 192. 168. 1. 15 or another unique IP Address that corresponds to the 192. 168. 1. X subnet. Use the Reset button located on the rear of the AP to revert to the default settings. I can't connect to other computers on my LAN. Windows network settings are not set correctly. Resolution: Make sure that each computer has a unique IP Address. Check each computer for correct network settings. TEW-410APBplus Wireless Troubleshooting I can't access the Wireless AP from a wireless network card Cause: Out of range. [. . . ]