User manual TRENDNET TEG-S2620IS

[. . . ] Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Working Port Num: The max number of ports can be aggregated at the same time. If LACP static trunk group, the exceed ports is standby and able to aggregate if work ports fail. If it is local static trunk group, the number must be the same as group ports. Select <Save> NOTE: Before set LACP support, you have to set trunk group on the Trunk Configuration. 51 LACP Working Ports configuration interface LACP State Activity 1. Select <Edit> Use "Space" key to select the Port State Activity. Passive: The port does not automatically send LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device. Select <Save>. 52 LACP State Activity configuration interface Group Status When you are setting trunk group, you can see the relation information in here. LACP Group State interface 53 IGMP/GVRP You can enable or disable the IGMP/GVRP (GARP VLAN Registration Protocol). Select <Edit> Use "Space" key to change the value Select <Save> IGMP/GVRP Configuration interface 54 802. 1x Configuration 802. 1x Configuration interface 802. 1x Setup 1. Select <Edit> Use "Space" key to Enable or Disable the 802. 1x. Select <Save> 55 802. 1x Setup interface System Configuration After enabling the IEEE 802. 1X function, you can configure the parameters of this function. Shared Key: set an encryption key for using during authentication sessions with the specified radius server. Server Port: set the UDP destination port for authentication requests to the specified Radius Server. Accounting Port: set the UDP destination port for accounting requests to the specified Radius Server. Select <Save>. 56 802. 1x System Configuration interface Per Port Configuration You can configure 802. 1x authentication state for each port. Use "Space" key change the state value. 802. 1x Per Port Setting interface 57 Misc Configuration 1. Select <Edit> Quiet Period: set the period during which the port doesn't try to acquire a supplicant. TX Period: set the period the port wait for retransmit next EAPOL PDU during an authentication session. Supplicant Timeout: set the period of time the switch waits for a supplicant response to an EAP request. Server Timeout: set the period of time the switch waits for a server response to an authentication request. Reauthorize Maximum: set the number of authentication that must time-out before authentication fails and the authentication session ends. Reauthorize period: set the period of time after which clients connected must be re-authenticated. Select <Save> 802. 1x Misc Configuration interface 58 System Reset Configuration You can reset the system back to default value, reboot the system and update the system firmware. System Reset Configuration interface Factory Default Reset switch to default configuration. [. . . ] Please refer to the following table for cable specifications. Cable Types and Specifications Cable 10BASE-T 100BASE-TX 100BASE-FX Type Cat. 5 100-ohm UTP 50/125 or 62. 5/125 micron core multimode fiber (MMF) Cable specification table Max. Length UTP 100 m (328 ft) 100 m (328 ft) 2 km (1. 24 miles) Connector RJ-45 RJ-45 SC or ST 100BASE-TX/10BASE-T Pin Assignments With 100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data. RJ-45 Pin Assignments 114 Pin Number 1 2 3 6 pair. Assignment Tx+ TxRx+ Rx- Note: "+" and "-" signs represent the polarity of the wires that make up each wire All ports on this switch support automatic MDI/MDI-X operation, you can use straight-through cables for all network connections to PCs or servers, or to other switches or hubs. [. . . ]