User manual TRENDNET TEG-S081FMI

[. . . ] Introduction The TEG-S081FMi Switch is compact desktop size switches which are ideal solutions for Fiber network infrastructure. It provides wire-speed, Fast Ethernet switching function that allows high-performance, low-cost connection. The Switch features a store-and-forward switching and it can auto-learn and MAC address on an 8K-entry MAC address table. Figure 1-1. The TEG-S081FMi Switch The Switch provides 8 100Mbps Fiber ports and one GBIC slot for optional GBIC modules. [. . . ] Passive: The port does not automatically sends LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device. Actions-> <Edit>: Configure all items. <Quit>: Exit this page and return to previous menu. 4-4-4-3. LACP Status When you setting trunking group, you can see relation information in here. 46 Actions-> <Quit>: Exit this page and return to previous menu. 4-5. Reboot Switch Default: Reset switch to default configuration. Restart: Reboot the switch in software reset. 47 Note: It may make the system setting parameter error that execut Default command and power off without wait consol appear "$$$ Press X key to start Xmodem receiver:" message if. Regarding this issue, user must wait console appear that message then can shut down power. Note: RS-232 Local console firmware upgrade (X modem ) 1. Press X key to start upgrading for Xmodem. First, disconnect terminal and modify baud rate to 57600bps, then do the connection again. 48 3. Select "send file" under "transfer" menu from menu bar. 5. Select "1K Xmodem" of protocol and press "Send" button. 6. After successfully upgraded the new firmware, please modify baud rate to 9600bps. 49 50 5. Web Management Function provides a Web browser to manage and monitor the switch, the default values as follows: If you need change IP address in first time, you can use console mode to modify it. IP Address: 192. 168. 16. 1 Subnet Mask: 255. 255. 255. 0 Default Gateway: 192. 168. 6. 254 User Name: root Password: root 2. You can browse http://192. 168. 16. 1, type user name and password as above. 5-1. port status State: Display port status off or on depended on user setting. Link Status: Down is "No Link", UP is "Link" Auto Negotiation: auto negotiation mode Speed status: Display link speed, Port 1- 8 is 100Mbps, Port 9 is 1000Mbps. Flow control: Display flow control status enable or disable mode Config: Display the state of user setting. The following information provides a view of the current status of the unit. 5-4. Administrator Those management functions include: IP address, Switch settings, Console port information, Port controls Link aggregation, Filter database, VLAN configuration , Spanning Tree, Port Mirror, SNMP, Security Manager, TFTP Update Firmware Configuration Backup, Reset system and Reboot. 54 5-4-1. User can configure the IP Settings and fill in the new value, than clicks apply button. User must be reset switch and use new IP address to browser this web management. Default IP:192. 168. 16. 1 Subnetmask:255. 255. 255. 0 Gateway:192. 168. 16. 254 55 5-4-2. MAC Address: The unique hardware address assigned by manufacturer (default) Firmware Version: Display the switch's firmware version. Kernel version: Display write to default EEPROM value version. 56 5-4-2-2. Advanced Miscellaneous Setting : MAC Address Age-out Time: Type the number of seconds that an inactive MAC address remains in the switch's address table. Max bridge transit delay bound control: Limit the packets queuing time in switch. Broadcast Storm Filter: To configure broadcast storm control, enable it and set the upper threshold for individual ports. The threshold is the percentage of the port's total bandwidth used by broadcast traffic. [. . . ] You can save current EEPROM value from here, then go to the TFTP restore configuration page to restore the EEPROM value. 5-4-14. Technical Specifications This section provides the specifications of 8 port Fiber plus GBIC Management Switch series, and the following table lists these specifications. Specifications Standards Compliance Protocol Max Forwarding and Max Filtering Rate LED Indicators IEEE 802. 3u 100Base- FX Fast Ethernet IEEE 802. 3z Gigabit Fiber CSMA/CD 14, 8800 pps per Fast Ethernet port, 148, 8000 pps per Gigabit Ethernet port (GBIC) Fiber Port : LINK/ACTIVE, Full Duplex/Collision ( 100Mbps Fiber port), Link/Active(GBIC port) Per Unit: Power Fiber Link Max. Distance Storage Temp. SC/ Multi-mode: Half-duplex: 412m, Full-duplex: 2Km -40ºC to 70ºC ( -40ºF to 158ºF) Operational Temp. 0ºC to 45ºC ( 32ºF to 113ºF ) Humidity 10% to 90% (Non-condensing) 81 External Power 100-240V AC, 50-60Hz 7. [. . . ]