User manual TRENDNET TE100-S810FI

[. . . ] Introduction In the modern society, communication and sharing information is essential to our lifestyle. Computer networks have proven to be one of the fastest methods of communication. The 8-port Management Switch series are compact desktop size switches which are ideal solutions for SOHO (Small Office or Home Office) network user. It provides wire-speed, Fast Ethernet switching function that allows high-performance, low-cost connection. [. . . ] After delete item press <Save> to complete the deleting operation. <Quit>: Exit this page and return to previous menu. 4-4-3. GVRP This page you can enable / disable the GVRP (GARP VLAN Registration Protocol) support. Press Space key to choose Enabled / Disabled. Actions-> <Edit>: Configure all items. <Quit>: Exit this page and return to previous menu. 43 4-4-4. LACP 4-4-4-1. Aggregator Setting 1. Group: Display the trunk group ID. 2. LACP: Press Space key to enable or disable LACP (Link Aggregation Control Protocol) support. 3. LACP Work Port Num: The max number of ports can be aggregated at the same time. If LACP static trunking group, the exceed ports is standby and able to aggregate if work ports fail. If local static trunking group, the number must be the same as group ports. NOTE: Before set LACP support, you have to set trunk group on the page of Port / Trunk Configuration first. Actions-> <Edit>: Configure all items. <Quit>: Exit this page and return to previous menu. 4-4-4-2. State Activity Active: The port automatically sends LACP protocol packets. Passive: The port does not automatically sends LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device. 45 Actions-> <Edit>: Configure all items. <Quit>: Exit this page and return to previous menu. 4-4-4-3. LACP Status When you setting trunking group, you can see relation information in here. Actions-> <Quit>: Exit this page and return to previous menu. <Next page>: Go to next page to view. 4-5. Reboot Switch Default: Reset switch to default configuration. First, disconnect terminal and modify baud rate to 57600bps, then do the connection again. 47 3. Select "send file" under "transfer" menu from menu bar. 5. Select "1K X-modem" of protocol and press "Send" button. 6. After successfully upgraded the new firmware, please modify baud rate to 9600bps. 5. Web-Based Management This section introduces the configuration and functions of the Web-based management of TE100-S810Fi series. The TE100-S810Fi series provides an embedded HTML website residing in flash memory. It offers management feature and allows users to manage the TE100-S810Fi from anywhere on the network through a standard Web Browser. NOTE: For those who use Win2000 have the Service Pack2 function, the web management function will have unexpected display if the IE version is below version 5. 5. 49 Web Management Function 1. Web Management Function provides a Web browser to manage and monitor the switch, the default values as follows: If you need change IP address in first time, you can use console mode to modify it. IP Address: 192. 168. 16. 1 Subnet Mask: 255. 255. 255. 0 Default Gateway:192. 168. 16. 254 User Name: root Password: root 2. You can browse http://192. 168. 16. 1, type user name and password as above. 5-1. port status State: Display port status off or on depended on user setting. [. . . ] Distance SC/MT-RJ/VF-45 Multi-mode: Half-duplex: 412m, Full-duplex: 2Km SC Single-mode: Half-duplex: 412m, Full-duplex: 15~60Km Dimensions Weight 250mm x 132mm x 37mm (L x W x H) 8TP Management Switch: 1060 g TE100-S810Fi series: 1080 ±20 g -40ºC to 70ºC ( -40ºF to 158ºF) Storage Temp. Operational Temp. 0ºC to 45ºC ( 32ºF to 113ºF ) Operational Humidity External Power Power Consumption 10% to 90% (Non-condensing) 100-240V AC, 50-60Hz 8TP Management Switch: 15 Watts (Max) TE100-S810Fi series: 17 Watts (Max) EMI Safety FCC Class A, CE Mark UL, cUL 7. Troubleshooting This section is intended to help you solve the most common problems on the 8TP/ TE100-S810Fi series. Incorrect connections Faulty or loose cables Look for loose or obviously faulty connections. IF that does not correct the problem, try a different cable. Non-standard cables Non-standard and miswired cables may cause numerous network collisions and other network problem, and can seriously impair network performance. [. . . ]