User manual TRENDNET TE100-S800I

[. . . ] Introduction The 8 10/100Base-TX Management Switch is a compact switch that is ideal for SOHO (Small Office or Home Office) networks. It provides wired-speeds, Fast Ethernet switching, and store-and-forward switching to attain high-performance at low-cost connections. It can also auto-learn and store source addresses on an 8K-entry MAC address table. The Switch provides 8 auto-sensing 10/100 Mbps RJ-45 Ethernet ports, supporting Auto-MDIX function for each port. [In general, MDI means connecting to another Hub or Switch while MDIX means connecting to a workstation or PC. [. . . ] 3. LACP Work Port Num: The max number of ports can be aggregated at the same time. If LACP static trunking group, the exceed ports is standby and able to aggregate if work ports fail. If local static trunking group, the number must be the same as group ports. NOTE: Before set LACP support, you have to set trunk group on the page of Port / Trunk Configuration first. Actions-> <Edit>: Configure all items. <Quit>: Exit this page and return to previous menu. 4-4-4-2. State Activity Active: The port automatically sends LACP protocol packets. Passive: The port does not automatically sends LACP protocol packets, and responds only if it receives LACP protocol packets from the opposite device. 46 Actions-> <Edit>: Configure all items. <Quit>: Exit this page and return to previous menu. 4-4-4-3. LACP Status When you setting trunking group, you can see relation information in here. Actions-> <Quit>: Exit this page and return to previous menu. <Next page>: Go to next page to view. 4-5. Reboot Switch Default: Reset switch to default configuration. First, disconnect terminal and modify baud rate to 57600bps, then do the connection again. 3. Select "send file" under "transfer" menu from menu bar. 4. Press "browse" button to select the path. 5. Select "1K X-modem" of protocol and press "Send" button. 6. After successfully upgraded the new firmware, please modify baud rate to 9600bps. 50 5. Web-Based Management This section introduces the configuration and functions of the Web-based management of 8TP+ 1Fiber Management Switch series. The 8TP+ 1Fiber Management Switch series provides an embedded HTML website residing in flash memory. It offers management feature and allows users to manage the 8TP+1Fiber Management Switch from anywhere on the network through a standard Web Browser. NOTE: For those who use Win2000 have the Service Pack2 function, the web management function will have unexpected display if the IE version is below version 5. 5. Web Management Function 1. Web Management Function provides a Web browser to manage and monitor the switch, the default values as follows: If you need change IP address in first time, you can use console mode to modify it. IP Address: Subnet Mask: 192. 168. 16. 1 255. 255. 255. 0 Default Gateway:192. 168. 16. 254 User Name: Password: root root 2. You can browse http://192. 168. 16. 1, type user name and password as above. 5-1. port status State: Display port status off or on depended on user setting. Link Status: Down is "No Link", UP is "Link" Auto Negotiation: auto negotiation mode Speed status: Display 100Mbps or 10Mbps speed, Port 1- 8 is 10/100Mbps. Flow control: Display flow control status enable or disable mode Config: Display the state of user setting. Actual: Display the negotiation result. 52 Click any of the virtual ports on the switch below to view each port's status. 5-3. The following information provides a view of the current status of the unit. 5-4. Administrator Those management functions include: IP address, Switch settings, Console port information, Port controls Link aggregation, Filter database, VLAN configuration , Spanning Tree, Port Mirror, SNMP, Security Manager, TFTP Update Firmware Configuration Backup, Reset system and Reboot. 5-4-1. User can configure the IP Settings and fill in the new value, than clicks apply button. [. . . ] You can restore EEPROM value from here, but you must put back image in TFTP server, switch will download back flash image. 5-4-13-2. TFTP Backup Configuration Use this page to set TFTP server IP address. You can save current EEPROM value from here, then go to the TFTP restore configuration page to restore the EEPROM value. 80 5-4-14. Reset System Reset Switch to default configuration, default value as below 5-4-15. [. . . ]