User manual TRENDNET TE100-S5P

[. . . ] Unpacking and Setup: Helps you get started with the basic installation of the Switch. Identifying External Components: Describes the front panel, rear panel and LED indicators of the Switch. Connecting the Switch: Explains how to connect the Switch to your Ethernet network. Technical Specifications: Lists the technical (general, physical and environmental, and performance) specifications of the Switch. [. . . ] Switches supporting both traditional 10Mbps Ethernet and 100Mbps Fast Ethernet are also ideal for bridging between the existing 10Mbps networks and the new 100Mbps networks. Switching LAN technology is a marked improvement over the 5 previous generation of network bridges, which were characterized by higher latencies. Routers have also been used to segment local area networks, but the cost of a router, the setup and maintenance required make routers relatively impractical. Today, switches are an ideal solution to most kinds of local area network congestion problems. Features The Switch was designed for easy installation and high performance in an environment where traffic on the network and the number of user increase continuously. The Switch with its small, compact size was specifically designed for small to mid size workgroups. This Switch can be installed where space is limited; moreover, they provide immediate access to a rapidly growing network through a wide range of user-reliable functions. The Switch is ideal for deployment with multiple high-speed servers for shared bandwidth 10Mbps or 100Mbps workgroups. With the highest bandwidth 200Mbps (100Mbps full-duplex mode), any port can provide workstations with a congestion-free data pipe for simultaneous access to the server. As all ports support 200Mbps, the Switch can be cascaded from any port and to any number of switches. The Switch is a perfect choice for site planning to upgrade to Fast Ethernet in the future. Ethernet workgroups can connect to the Switch now, and change adapters and hubs anytime later without needing to change the Switches or reconfigure the network. The Switch combine dynamic memory a llocation with store-andforward switching to ensure that the buffer is effectively allocated for each port, while controlling the data flow between the transmit and 6 receive nodes to guarantee against all possible packet loss. The Switch is an unmanaged 10/100 Fast Ethernet Switch that offers solutions in increasing small Ethernet/Fast Ethernet workgroup bandwidth. As the result of complete frame checking and error frame filtering, this scheme prevents error packages from transmitting among segments. Auto-MDI function supports automatic MDI/MDIX crossover detection function gives true `plug and play' capability without the need of confusing crossover cables or crossover ports. This allows for auto-sensing of speed (10/100Mbps) thereby providing you with automatic and flexible solutions in your network connections. This minimizes dropped packets by sending out collision signals when the port's receiving buffer is full. Data filtering rate eliminates all error packets, runts, etc. , per port at wire-speed for 100Mbps speed. Data filtering rate eliminates all error packets, runts, etc. , per port at wire-speed for 10Mbps speed. 7 UNPACKING AND SETUP This chapter provides unpacking and setup information for the Switch. Unpacking Open the box of the Switch and carefully unpack it. The box should contain the following items: One 5 or 8-port 10/100M Fast Ethernet Switch One External AC Power Adapter This User's Guide If any item is found missing or damaged, please contact your local reseller for replacement. Setup The setup of the Switch can be performed using the following steps: ??Visually inspect the DC power jack and make sure that it is securely connected to the power adapter. Make sure that there is proper heat dissipation from and adequate ventilation around the Switch. [. . . ] This LED blinks green when collisions occur on the respective port. Note: It is normal to see some collisions in the network. If a Port's Collision LED is on constantly, check the status of the device the port is connected to. 11 For 8-port switch Power Indicator (PWR) This indicator lights green when the hub is receiving power. LINK / ACT (Link/Activity) (green) This indicator lights green when the port is connected to a Fast Ethernet or Ethernet device. Each port on the Switch has auto-MDI function; you can make the connection using crossover or straight through cable with uplink port or regular port from the device. Port Speed & Duplex Mode After a connection is made the Switch uses auto-negotiation to determine the transmission mode for this twisted-pair connection. [. . . ]