User manual TRENDNET TE100-PCBUSR

[. . . ] Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. VCCI Mark Warning Table of Contents INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 LED INDICATORS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The PC Card will then protrude from the PC Card slot and you can easily remove the PC Card by gripping its protruding end and withdrawing it from the PC Card receptacle. Driver Installation Before you connect the 32-bit CardBus 10/100Mbps Fast Ethernet PC Card to the network, you have to install the network driver first. The driver for each networking operating system is under a separate directory. A HELP8139. EXE file under root directory lists the information and detailed installation procedure of all the available drivers. Card insertion as described in Chapter "Card Insertion and Removal" must be completed before you proceed with software installation. Windows XP/Vista Installation The PC card will automatically be detected and install drivers from Windows XP/Vista operating systems, there is no need to use the CD-ROM that is supplied with this PC card. In the event that the PC card cannot be installed with the Windows operating system drivers then, use the driver supplied with this PC card. 7 Diagnostics If you experience any problems with the 32-bit CardBus 10/100Mbps Fast Ethernet PC Card, first verify that the appropriate driver is loaded, that the proper grade of cable is employed for the network connection, and that the supporting hub/switch is functioning properly. As certain that the 32-bit CardBus 10/100Mbps Fast Ethernet PC Card is fully and firmly seated in the 32-bit CardBus PC Card slot. Replace the adapter in question with a verified adapter and run ENCBRSET. BAT diagnostic tests on the CD-ROM at directory of \Rset\. Install the questioned adapter in another notebook PC and run the tests again. Remove all other PC Card from the notebook PC and run the tests again. If the diagnostic run is abnormal, then there is probably an interrupt number conflict that will 8 have to be resolved manually by a CMOS Setup utility run after you have reinstalled all of the expansion cards. The Diagnostic Program provides two levels of testing: Adapter Basic Diagnostics and Network Diagnostics. Adapter Basic Diagnostic does not require substitution of a loopback cable. All procedures of the Adapter test may be carried out with the network cable connection in place. For the Network Diagnostics, the cable connecting your station with its supporting hub/switch must be in place. Network Diagnostic involves "broadcast" transmission of test packets from the initiator station. The test cannot be fully implemented unless a responder station on the LAN is available to the Network Diagnostics, in order to return the test packets to the initiator station. To run the Diagnostic Program, proceed with these steps: Adapter Basic Diagnostics 1. Insert the 32-bit CardBus 10/100Mbps Fast Ethernet PC Card driver CD in an available drive (here shown as drive D). At the DOS prompt (here shown as >), key in: > D: \Rset\ENCBRSET. BAT and <Enter>. Review the reported configuration data before proceeding to Step 3. [. . . ] 5 EIA/TIA- 568 100-ohm STP Physical and Environmental Temperature Operating: 0° ~ 50° C, Storage: -10° ~ 70° C 10 Humidity EMI: Operating: 10% ~ 90%, Storage: 5% ~ 90% FCC Class B, CE Mark B, VCCI-B 11 Limited Warranty TRENDware warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TE100-PCBUSR ­ 5 Years Warranty If a product does not operate as warranted above during the applicable warranty period, TRENDware shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective item, or refund to customer the purchase price paid for the defective product. Replacement products may be new or reconditioned. TRENDware shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDware pursuant to any warranty. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual. Warranty service may be obtained by contacting TRENDware office within the applicable warranty period for a Return Material Authorization (RMA) number, accompanied by a copy of the dated proof of the purchase. [. . . ]