User manual TRENDNET TE100-P1U

[. . . ] TABLE OF CONTENTS ABOUT THIS GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PACKAGE CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 SYSTEM REQUIREMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · Browse CD ­ if you want to browse the contents of the Installation CD-ROM, click this button and the contents of the CD will be available for preview. If no specific requirement, leave the default setting and click Next >. - 13 - - 14 - 3. The InstallShield Wizard starts to install the software, and the Progress bar indicates the installation is proceeding. The main screen will appear as below, and it starts to search the connected print server within the network. Your print server After installing the utility, the application program for the print server is automatically installed to your computer, and creates a folder in Start\Programs\PS-Utility. Using PS-Utility This section describes the operation of PS-Utility. Control Buttons - Change IP Address: Click this button to bring up the following dialog box, allowing you to change the IP Address. In this dialog box, you can select either Manually Assign or DHCP Assign Automatically. Click Start -> Programs -> PS-Utility, and then click the PSUtility v2. 00 item. - 15 - - 16 - - - Update Firmware: Click this button to update the firmware of the selected print server. Show Web Setup: Click this button to open your web browser and launch the Configuration Utility. Alternately, you can double-click the print server in the Device List to launch the Configuration Utility. Factory Reset: Click this button to reload the factory settings of the print server. Discover Device: Click this button to search the connected print server again. About: Click this button to bring up a window containing the basic information of PS-Utility. Close: Click this button to exit PS-Utility. 4 WEB CONFIGURATION You can access and manage the Print Server through: 1) the enclosed software PS-Utility, and 2) a web browser. This chapter describes the second method ­ the Web Configuration Utility, and explains how to set up your print server with the web browser. 3. Information Field: Display the basic information of the selected print server in the Device List. Status Bar: Display the system status. Web Configuration Utility First, launch your web browser (such as the Internet Explorer 6. 0 used in this manual). Then, type http://192. 168. 0. 1 (the default IP address) in the Address bar and press [Enter] to enter the Management screen of the Configuration Utility. TIP: The computer's IP address must correspond with the print server's IP address in the same segment for the two devices to communicate. Extensive knowledge of LAN will be helpful in configuring the print server. - 17 - - 18 - Home Setup Wizard The Management Screen of the Configuration Utility The "Setup Wizard" will lead you to change all the configurations step by step. Make sure that you have installed the TCP/IP protocol, and have properly configured the Windows 95/98/Me TCP/IP settings. You can install the protocol from the Network control panel if necessary. The Print Server can provide print services to TCP/IP networks using the lpr/lpd network printing protocol. Most UNIX systems are capable of supporting lpd, as is Windows NT/2000. This LPR for TCP/IP Printing client gives Windows 95/98/Me workstations the ability to print using the lpr/lpd printing protocol. [. . . ] Select the correct Make and Model, or click "Have Disk", to provide the Manufacturer's Driver Disk. Click "Next". Click "Finish" Select a "Printer Name". - 51 - - 52 - A Test Page can be printed to confirm proper configuration. 7 PRINTING IN MAC OS Rendezvous Uses in MAC OS 10. 2 The latest version of MAC OS provides a new feature that is called Rendezvous. Rendezvous is a revolutionary networking technology standard that lets you create an instant network of computers and devices, which can be used throughout Mac OS 10. 2 to provide innovative ways to share files and printers and even contact other people on the network. For the printer connection, the Mac OS 10. 2 Print Center application uses Rendezvous to discover Rendezvous-enabled printers on the network. [. . . ]