User manual TRANSCEND TS4GJFT5W

[. . . ] Complaint with CFast 1. 0 standard, CFast is your best choice as an embedded SATA storage solution. . Placement · · · · · Support S. M. A. R. T (Self-defined) Support Security Command Fully compatible with devices and OS that support the SATA 3Gb/s standard Non-volatile SLC Flash Memory for outstanding data retention Durability of Connector: 10, 000 times Dimensions Side A B C D Millimeters 42. 8 36. 4 3. 3 0. 6 Inches 1. 685 1. 433 0. 13 0. 02 Transcend Information Inc. 1 V0. 5 TS2G~16GCFX500 Specifications Physical Specification Form Factor Storage Capacities Length Dimensions (mm) Width Height Input Voltage Weight Connector CFast 2GB~16 GB 42. 8 ± 0. 1 36. 4 ± 0. 15 3. 3 ± 0. 1 3. 3V ± 5% TBD CFAST connector CFast Card Environmental Specifications Operating Temperature Storage Temperature Humidity Operating Non-Operating 0 to 70 - 40 to 85 0% to 95% (Non-condensing) 0% to 95% (Non-condensing) Regulations Compliance CE, FCC and BSMI Performance Model P/N TS2GCFX500 TS4GJFT5W TS8GCFX500 TS16GCFX500 Read 56 MB/s 56 MB/s 102 MB/s 108 MB/s Write 27MB/s 49MB/s 88MB/s 91MB/s ® Random Read 50 MB/s 50 MB/s 83MB/s 89 MB/s Random Write 8 MB/s 12 MB/s 17 MB/s 18 MB/s Note: 25 , test on ASUS P4S800-MX, 1GB RAM, Windows XP Version 2002 SP2, benchmark utility HDBENCH (version 3. 4006), copied file 1GB. Transcend Information Inc. 2 V0. 5 TS2G~16GCFX500 Actual Capacity Model P/N TS2GCFX500 TS4GJFT5W TS8GCFX500 TS16GCFX500 User Max. LBA 3, 865, 680 7, 732, 368/ 15, 465, 344 30, 932, 992 Cylinder 3, 835 7, 671 15, 343 16, 383 CFast Card Head 16 16 16 15 Sector 63 63 63 63 Power Requirements Input Voltage Mode Write(peak) Power Consumption Read(peak) Idle(peak) 3. 3V ± 5% Max. (mA) 352 371 141 SHOCK & Vibration Test Condition Mechanical Shock Test Vibration Test 1500G, 0. 5ms, 3 axis 20G (Peak-to-Peak) 20Hz to 2000Hz (Frequency) Standard IEC 60068-2-27 IEC 60068-2-6 Transcend Information Inc. 3 V0. 5 TS2G~16GCFX500 Package Dimensions Below figure illustrates the Transcend CFastTM. [. . . ] Host locks ­ after detecting the COMWAKE, the host starts transmitting D10. 2 characters at its lowest supported rate. Meanwhile, the host receiver locks to the ALIGN sequence and, when ready, returns the ALIGN sequence to the device at the same speed as received. A host shall be designed such that it acquires lock in 54. 6us (2048 nominal Gen1 Dword times) at any given speed. The host should allow for at least 873. 8 us (32768 nominal Gen1 Dword times) after detecting the release of COMWAKE to receive the first ALIGNP. This ensures interoperability with multi-generational and synchronous designs. If no ALIGNP is received within 873. 8 us (32768 nominal Gen1 Dword times) the host restarts the power-on sequence ­ repeating indefinitely until told to stop by the Application layer. Device locks ­ the device locks to the ALIGN sequence and, when ready, sends SYNCP indicating it is ready to start normal operation. Upon receipt of three back-to-back non-ALIGNP primitives, the communication link is established and normal operation may begin. Transcend Information Inc. 10 V0. 5 TS2G~16GCFX500 COMINIT CFast Card COMINIT always originates from the drive and requests a communication initialization. It is electrically identical to the COMRESET signal except that it originates from the device and is sent to the host. It is used by the device to request a reset from the host in accordance to the sequence shown in Figure 6, below. Figure 6 : cominit sequence Description: 1. Host/device are powered and operating normally with some form of active communication. If additional speeds are available the device tries the next lower supported speed by sending ALIGNP primitives at that rate for 54. 6 us (2048 nominal Gen1 Dword times. ) This step is repeated for as many slower speeds as are supported. Once the lowest speed has been reached without response from the host, the device shall enter an error state. If there is data in the write cache, that data shall be written to the media. The BSY bit shall remain set to one until all data has been successfully written or an error occurs. IDENTIFY DEVICE (ECh) This commands read out 512Bytes of drive parameter information. Parameter Information consists of the arrangement and value as shown in the following table. This command enables the host to receive the Identify Drive Information from the device. Transcend Information Inc. 15 V0. 5 TS2G~16GCFX500 Word Address 0 1 2 3 4 5 6 7-8 9 10-19 20 21 22 23-26 27-46 47 Word Address 48 49 50 51 52 53 54 55 56 57-58 59 60-61 62 63 64 65 Default Value 044Ah XXXXh 0000h 00XXh 0000h 0240h XXXXh XXXXh 0000h aaaa 0002h 0002h 0004h aaaa aaaa 8001h Default Value 0000h 0F00h 4000h 0200h 0000h 0007h XXXXh 00XXh XXXXh XXXXh 01XXh XXXXh 0000h 0007h 0003h 0078h Total Bytes 2 2 2 2 2 2 2 4 2 20 2 2 2 8 40 2 Total Bytes 2 2 2 2 2 2 2 2 2 4 2 4 2 2 2 2 Reserved Capabilities Capabilities PIO data transfer cycle timing mode Obsolete Field Validity Current numbers of cylinders Current numbers of heads Current sectors per track General configuration Default number of cylinders Reserved Default number of heads Obsolete Obsolete Default number of sectors per track CFast Card Identify Device Information Default Value Data Field Type Information Number of sectors per card (Word 7 = MSW, Word 8 = LSW) Obsolete Serial number in ASCII (Right Justified) Obsolete Obsolete Obsolete Firmware revision in ASCII. Big Endian Byte Order in Word Model number in ASCII (Left Justified) Big Endian Byte Order in Word Maximum number of sectors on Read/Write Multiple command Data Field Type Information Current capacity in sectors (LBAs)(Word 57 = LSW, Word 58 = MSW) Multiple sector setting Total number of sectors addressable in LBA Mode Reserved Multiword DMA transfer. Supports MDMA Mode 0, 1, and 2 Advanced PIO modes supported Minimum Multiword DMA transfer cycle time per word. In PC Card modes this value shall be 0h Transcend Information Inc. 16 V0. 5 TS2G~16GCFX500 66 67 68 69-75 76 77-79 80 81 82 83 84 85-87 88 89 90 91 92 Word Address 93-127 128 129-159 160 161 162 163 164 165-175 176-255 0078h 0078h 0078h 0000h 0006h 000h 0080h 0000h 742Bh 550Ch 4002h XXXXh 047Fh 0001h 0000h 0000h FFFEh Default Value 0000h 0001h 0000h 81F4h 0000h 0000h 0000h 0000h 0000h 0000h 2 2 2 14 2 6 2 2 2 2 2 6 2 2 2 2 2 Total Bytes 70 2 64 2 2 2 2 2 22 140 Reserved Security status Vendor unique bytes Power requirement description Reserved Key management schemes supported CFast Card Recommended Multiword DMA transfer cycle time. In PC Card modes this value shall be 0h Minimum PIO transfer cycle time without flow control Minimum PIO transfer cycle time with IORDY flow control Reserved Serial ATA capacities Support Serial ATA Gen1 Support Serial ATA Gen2 Reserved Minor version number (ATAPI-7) Minor version number Command sets supported 0 Command sets supported 1 Command sets supported 2 Features/command sets enabled Ultra DMA Mode Supported and Selected Time required for Security erase unit completion Time required for Enhanced security erase unit completion Current Advanced power management value Master Password Revision Code Data Field Type Information CF Advanced True IDE Timing Mode Capability and Setting Reserved Reserved Reserved Transcend Information Inc. 17 V0. 5 TS2G~16GCFX500 READ DMA (C8h) CFast Card Read data from sectors during Ultra DMA and Multiword DMA transfer. A sector count of zero requests 256 sectors. READ MULTIPLE (C4h) This command performs similarly to the Read Sectors command. [. . . ] The host transfers 512 bytes of data, as shown in the following table, to the drive. The transferred data contains a user or master password, which the drive compares with the saved password. It is re-enabled by issuing the SECURITY SET PASSWORD command to re-set a user password. SECURITY ERASE PREPARE (F3h) This command shall be issued immediately before the Security Erase Unit command to enable erasing and unlocking. This command prevents accidental loss of data on the drive. SECURITY ERASE UNIT (F4h) The host uses this command to transfer 512 bytes of data, as shown in the following table, to the drive. [. . . ]