User manual TRANSCEND TS32GCF200I DATASHEET

[. . . ] Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Description The Transcend CF200I is a High Speed industrial Compact Flash Card with high quality Flash Memory assembled on a printed circuit board. Features · CompactFlash Specification Version 4. 1 Compliant · RoHS compliant products · Single Power Supply: 3. 3V±5% or 5V±10% · Operating Temperature: -40 C to 85 C o o o o Placement · Storage Temperature: -55 C to 100 C · Humidity (Non condensation): 0% to 95% · Built-in 13/24-bit ECC (Error Correction Code) functionality and wear-leveling algorithm ensures highly reliable of data transfer 13bit BCH ECC (2k+64 / 4k+128 byte per page flash) 24bit BCH ECC (4k+208 byte per page flash) · Operation Modes: PC Card Memory Mode PC Card IO Mode True DE Mode · True IDE Mode supports: Ultra DMA Mode 0 to 5 (UDMA4 as default) Dimensions Multi-Word DMA Mode 0 to 4 PIO Mode 0 to 6 · True IDE Mode: Fixed Disk (Default) · PC Card Mode: Fixed Disk (Default) · Durability of Connector: 10, 000 times · MTBF: 2, 000, 000 hours (in 25) · Support Global Wear-Leveling, Static Data Refresh, Early Retirement, and Erase Count Monitor functions to extend product life · Support S. M. A. R. T (Self-defined) · Support Security Command · Compliant to CompactFlash, PCMCIA, and ATA standards Transcend Information Inc. 1 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Ordering Information Part Number Interface Transfer Mode Ultra DMA mode 0~5 True IDE mode TS128M~16GCF200I (UDMA4 as default) Multi-Word DMA Mode 0~4 PIO Mode 0 ~ 6 PC Card mode (PCMCIA) 80ns, 100ns, 120ns, 250ns Fixed Disk (Default) Fixed Disk (Default) Disk Type C. H. S Table Capacity 128MB 256MB 512MB 1GB 2GB 4GB 8GB 16GB 32GB C 246 493 987 1974 3949 7899 15798 16383 16383 H 16 16 16 16 16 16 16 15 15 S 63 63 63 63 63 63 63 63 63 Physical Capacity 126, 959, 616 bytes 254, 435, 328 bytes 509, 386, 752 bytes 1, 018, 773, 504 bytes 2, 038, 063, 104 bytes 4, 076, 642, 304 bytes 8, 153, 284, 608 bytes 16, 039, 018, 496 bytes 32, 019, 316, 736 bytes Note: FAT format for <4GB, FAT32 format for 4~32GB Performance Model P/N TS128MCF200I TS256MCF200I TS512MCF200I TS1GCF200I TS2GCF200I TS4GCF200I TS8GCF200I TS16GCF200I TS32GCF200I Read (KB/s) 25440 25940 25940 29111 28804 28784 49349 50381 51979 Write (KB/s) 7362 10697 10317 12363 20791 22200 36900 39689 35992 Random Read (KB/s) 24482 24719 24482 27563 27288 26736 44425 46757 48165 Random Write (KB/s) 2559 3513 3390 4121 5079 6635 11966 10739 7892 * Note : 25 , according to CF to IDE connector test on P5K-VM, 1GB RAM * 2, IDE interface support UDMA4, Transcend Information Inc. 2 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Windows XP Version 2002 SP2, benchmark utility FDBENCH (version 1. 02), copied file 40MB ® Power Requirements (DC 5V, 3. 3V @25) Part Number & Input Voltage 3. 3V ± 10% 5V ± 10% 3. 3V ± 10% 5V ± 10% 3. 3V ± 10% 5V ± 10% 3. 3V ± 10% 5V ± 10% 3. 3V ± 10% 5V ± 10% 3. 3V ± 10% 5V ± 10% 3. 3V ± 10% 5V ± 10% 3. 3V ± 10% 5V ± 10% 3. 3V ± 10% 5V ± 10% Current Magnitude (mA) Read 61 102. 6 61. 3 99 86. 9 64. 1 67. 5 71. 3 71 116 69. 6 113. 8 88. 6 99. 9 139. 5 173. 4 142. 0 165. 8 Write 52. 6 53. 4 57. 6 58. 8 57. 8 59. 3 65. 9 68. 6 89. 6 93. 1 89. 2 98. 9 137. 1 139. 9 143. 4 152. 6 131. 9 143. 5 TS128MCF200I TS256MCF200I TS512MCF200I TS1GCF200I TS2GCF200I TS4GCF200I TS8GCF200I TS16GCF200I TS32GCF200I 1. Read/Write operation is drived by IOMeter with 10MB file each operation. All data above are maximum value of each measurements. SHOCK & Vibration Test Condition Mechanical Shock Test Vibration Test 1500G, 0. 5ms, 3 axes 20G (Peak-to-Peak) 20Hz to 2000Hz (Frequency) Standard IEC 60068-2-27 IEC 60068-2-6 Regulations Compliance CE, FCC and BSMI 3 V1. 2 Transcend Information Inc. Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 More Functions to extend product life 1. Global Wear Leveling ­ Advanced algorithm to enhance the Wear-Leveling Efficiency There are 3 main processes in global wear leveling approaches: (1) Record the block erase count and save in the wear-leveling table. [. . . ] Bit 2 (SW Rst): this bit is set to 1 in order to force the CompactFlash Storage Card to perform an AT Disk controller Soft Reset operation. This does not change the PCMCIA Card Configuration Registers as a hardware Reset does. The Card remains in Reset until this bit is reset to `0. ' Bit 1 (-IEn): the Interrupt Enable bit enables interrupts when the bit is 0. When the bit is 1, interrupts from the CompactFlash Storage Card are disabled. This bit also controls the Int bit in the Configuration and Status Register. Bit 0: this bit is ignored by the CompactFlash Storage Card. Transcend Information Inc. 54 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Card (Drive) Address Register (Address 3F7h[377h]; Offset Fh) This register is provided for compatibility with the AT disk drive interface. It is recommended that this register not be mapped into the host's I/O space because of potential conflicts on Bit 7. Bit 7: this bit is unknown. Implementation Note: Conflicts may occur on the host data bus when this bit is provided by a Floppy Disk Controller operating at the same addresses as the CompactFlash Storage Card. Following are some possible solutions to this problem for the PCMCIA implementation: 1) Locate the CompactFlash Storage Card at a non-conflicting address, i. e. Secondary address (377) or in an independently decoded Address Space when a Floppy Disk Controller is located at the Primary addresses. 2) Do not install a Floppy and a CompactFlash Storage Card in the system at the same time. 3) Implement a socket adapter that can be programmed to (conditionally) tri-state D7 of I/0 address 3F7h/377h when a CompactFlash Storage Card is installed and conversely to tristate D6-D0 of I/O address 3F7h/377h when a floppy controller is installed. 4) Do not use the CompactFlash Storage Card's Drive Address register. This may be accomplished by either a) If possible, program the host adapter to enable only I/O addresses 1F0h-1F7h, 3F6h (or 170h-177h, 176h) to the CompactFlash Storage Card or b) if provided use an additional Primary / Secondary configuration in the CompactFlash Storage Card which does not respond to accesses to I/O locations 3F7h and 377h. With either of these implementations, the host software shall not attempt to use information in the Drive Address Register. Bit 6 (-WTG): this bit is 0 when a write operation is in progress; otherwise, it is 1. Bit 5 (-HS3): this bit is the negation of bit 3 in the Drive/Head register. Bit 4 (-HS2): this bit is the negation of bit 2 in the Drive/Head register. Bit 3 (-HS1): this bit is the negation of bit 1 in the Drive/Head register. Bit 2 (-HS0): this bit is the negation of bit 0 in the Drive/Head register. Bit 0 (-nDS0): this bit is 0 when the drive 0 is active and selected. Transcend Information Inc. 55 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 CF-ATA Command Set Transcend Information Inc. 56 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Transcend Information Inc. 57 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Request Sense - 03h The extended error code is returned to the host in the Error Register. Write Sector(s) without Erase - 38h Transcend Information Inc. 58 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Erase Sector(s) - C0h This command is used to pre-erase and condition data sectors in advance of a Write without Erase or Write Multiple without Erase command. There is no data transfer associated with this command but a Write Fault error status can occur. Write Multiple without Erase ­ CDh Translate Sector - 87h Transcend Information Inc. 59 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Translate Sector Information Transcend Information Inc. 60 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Set Features ­ EFh Feature Supported Feature 03h 81h 82h Operation Set transfer mode based on calue in Sector Count register Disable 8 bit data transfer Disable Write Cache Execute Drive Diagnostic - 90h When the diagnostic command is issued in a PCMCIA configuration mode, this command runs only on the CompactFlash Storage Card that is addressed by the Drive/Head register. [. . . ] Bits 1-15 are reserved for future additional Key Management schemes. Transcend Information Inc. 82 V1. 2 Transcend IIndustriiall CF Card Transcend ndustr a CF Card TS128M~32GCF200II TS128M~32GCF200 Word 163: CF Advanced True IDE Timing Mode Capabilities and Settings This word describes the capabilities and current settings for CFA defined advanced timing modes using the True IDE interface. The use of True IDE PIO Modes 5 and above or of Multiword DMA Modes 3 and above impose significant restrictions on the implementation of the host: Additional Requirements for CF Advanced Timing Modes. There are four separate fields defined that describe support and selection of Advanced PIO timing modes and Advanced Multiword DMA timing modes. Word 63: Multiword DMA transfer and 6. 2. 1. 6. 19: Word 64: Advanced PIO transfer modes supported. [. . . ]