User manual TRANSCEND TS2GCF45I-D QUICK INSTRUCTION GUIDE

[. . . ] TSxGMSA300 Built-in 15-bit/512Byte ECC (Error Correction Code) functionality ensures highly reliable of Placement · data transfer. Global wear-leveling algorithm eliminates excessive write operation and extends product life. · Support StaticDataRefresh & EarlyRetirement technology to monitor error bit level and react before data is corrupted. · · · Support S. M. A. R. T (Self-defined) Support Security Command Fully compatible with devices and OS that support the SATA 3Gb/s standard Non-volatile SLC/MLC Flash Memory for outstanding data retention · Dimensions Side W L H Millimeters 29. 85 50. 80 3. 5 Inches 1. 175 2. 000 0. 137 Transcend Information Inc. 1 V1. 3 TS2G~16GMSA500 TS16G~64GMSA300 Specifications Physical Specification Form Factor Storage Capacities Length Dimensions (mm) Width Height Input Voltage Weight Connector MO-300 2GB~64GB 50. 8 ± 0. 15 29. 85 ± 0. 15 3. 5 ± 0. 1 3. 3V ± 5% 9g PCI Express Mini Card Connector mSATA SSD Environmental Specifications Operating Temperature Storage Temperature Humidity Operating Non-Operating 0 to 70 -40 to 85 0% to 95% (Non-condensing) 0% to 95% (Non-condensing) Regulations Compliance CE, FCC and BSMI Performance Model P/N TS2GCF45I-D TS4GMSA500 TS2GCF45I-D TS16GMSA500 Read 50 MB/s 50 MB/s 100 MB/s 100 MB/s Write 25 MB/s 45 MB/s 80 MB/s 90 MB/s Random Read 50 MB/s 50 MB/s 80 MB/s 80 MB/s Random Write 8 MB/s 12 MB/s 15 MB/s 15 MB/s Performance Model P/N TS16GMSA300 TS32GMSA300 TS64GMSA300 Read 95 MB/s 95 MB/s 95 MB/s Write 15 MB/s 20 MB/s 30 MB/s 2 V1. 3 Random Read 55 MB/s 70 MB/s 55 MB/s Random Write 5 MB/s 5 MB/s 9 MB/s Transcend Information Inc. TS2G~16GMSA500 TS16G~64GMSA300 ® mSATA SSD Note:25 , Typical value, test on ASUS P4S800-MX, 1GB RAM, Windows XP Version 2002 SP2, benchmark utility HDBENCH (version 3. 4006), copied file 1GB Actual Capacity Model P/N TS2GCF45I-D TS4GMSA500 TS2GCF45I-D TS16GMSA500 TS16GMSA300 TS32GMSA300 TS64GMSA300 User Max. LBA 3, 865, 680 7, 732, 368 15, 465, 344 30, 932, 992 30, 932, 992 61, 865, 984 123, 731, 968 Cylinder 3, 835 7, 671 15, 343 16, 383 16, 383 16. 383 16, 383 Head 16 16 16 15 15 15 15 Sector 63 63 63 63 63 63 63 Power Requirements Input Voltage Mode Write(peak) Power Consumption Read(peak) Idle(peak) 3. 3V ± 5% Max. [. . . ] Following calibration the device sends a six burst COMWAKE sequence and then sends a continuous stream of the ALIGN sequence starting at the device's highest supported speed. After ALIGNP Dwords have been sent for 54. 6us (2048 nominal Gen1 Dword times) without a response from the host as determined by detection of ALIGNP primitives received from the host, the device assumes that the host cannot communicate at that speed. If additional speeds are available the device tries the next lower supported speed by sending ALIGNP Dwords at that rate for 54. 6 us (2048 nominal Gen1 Dword times. ) This step is repeated for as many slower speeds as are supported. Once the lowest speed has been reached without response from the host, the device enters an error state. Host locks ­ after detecting the COMWAKE, the host starts transmitting D10. 2 characters at its lowest supported rate. Meanwhile, the host receiver locks to the ALIGN sequence and, when ready, returns the ALIGN sequence to the device at the same speed as received. A host shall be designed such that it acquires lock in 54. 6us (2048 nominal Gen1 Dword times) at any given speed. The host should allow for at least 873. 8 us (32768 nominal Gen1 Dword times) after detecting the release of COMWAKE to receive the first ALIGNP. This ensures interoperability with multi-generational and synchronous designs. If no ALIGNP is received within 873. 8 us (32768 nominal Gen1 Dword times) the host restarts the power-on sequence ­ repeating indefinitely until told to stop by the Application layer. Device locks ­ the device locks to the ALIGN sequence and, when ready, sends SYNCP indicating it is ready to start normal operation. Support ATA/ATAPI Command General Feature Set EXECUTE DIAGNOSTICS FLUSH CACHE IDENTIFY DEVICE READ DMA READ MULTIPLE READ SECTOR(S) READ VERIFY SECTOR(S) SET FEATURES SET MULTIPLE MODE WRITE DMA WRITE MULTIPLE WRITE SECTOR(S) NOP READ BUFFER WRITE BUFFER 90h E7h ECh C8h C4h 20h 40h or 41h EFh C6h CAh C5h 30h 00h E4h E8h E5h or 98h E3h or 97h E1h or 95h E6h or 99h E2h or 96h E0h or 94h F1h F2h F3h F4h F5h F6h B0h B0h B0h B0h B0h B0h F8h F9h F9h F9h F9h F9h mSATA SSD Code Protocol Device diagnostic Non-data PIO data-In DMA PIO data-In PIO data-In Non-data Non-data Non-data DMA PIO data-out PIO data-out Non-data PIO data-In PIO data-out Non-data Non-data Non-data Non-data Non-data Non-data PIO data-out PIO data-out Non-data PIO data-out Non-data PIO data-out Non-data Non-data Non-data Non-data Non-data PIO data-In Non-data Non-data PIO data-out Non-data Non-data PIO data-out Power Management Feature Set CHECK POWER MODE IDLE IDLE IMMEDIATE SLEEP STANDBY STANDBY IMMEDIATE Security Mode Feature Set SECURITY SET PASSWORD SECURITY UNLOCK SECURITY ERASE PREPARE SECURITY ERASE UNIT SECURITY FREEZE LOCK SECURITY DISABLE PASSWORD SMART Feature Set SMART Disable Operations SMART Enable/Disable Autosave SMART Enable Operations SMART Return Status SMART Execute Off-Line Immediate SMART Read Data Host Protected Area Feature Set Read Native Max Address Set Max Address Set Max Set Password Set Max Lock Set Max Freeze Lock Set Max Unlock Transcend Information Inc. 14 V1. 3 TS2G~16GMSA500 TS16G~64GMSA300 ATA Command Specifications FLUSH CACHE (E7h) mSATA SSD The host uses this command to request the device to flush the write cache. If there is data in the write cache, that data shall be written to the media. The BSY bit shall remain set to one until all data has been successfully written or an error occurs. IDENTIFY DEVICE (ECh) This commands read out 512Bytes of drive parameter information. Parameter Information consists of the arrangement and value as shown in the following table. This command enables the host to receive the Identify Drive Information from the device. Identify Device Information Default Value Word Address 0 1 2 3 4 5 6 7-8 9 10-19 20 21 22 23-26 27-46 47 Default Value 044Ah XXXXh 0000h 00XXh 0000h 0240h XXXXh XXXXh 0000h aaaa 0002h 0002h 0004h aaaa aaaa 8001h Total Bytes 2 2 2 2 2 2 2 4 2 20 2 2 2 8 40 2 General configuration Default number of cylinders Reserved Default number of heads Obsolete Obsolete Default number of sectors per track Number of sectors per card (Word 7 = MSW, Word 8 = LSW) Obsolete Serial number in ASCII (Right Justified) Obsolete Obsolete Obsolete Firmware revision in ASCII. Big Endian Byte Order in Word Model number in ASCII (Left Justified) Big Endian Byte Order in Word Maximum number of sectors on Read/Write Multiple command Data Field Type Information Transcend Information Inc. 15 V1. 3 TS2G~16GMSA500 TS16G~64GMSA300 Word Address 48 49 50 51 52 53 54 55 56 57-58 59 60-61 62 63 64 65 66 67 68 69-75 76 77-79 80 81 82 83 84 85-87 88 89 90 91 92 Default Value 0000h 0F00h 4000h 0200h 0000h 0007h XXXXh 00XXh XXXXh XXXXh 01XXh XXXXh 0000h 0007h 0003h 0078h 0078h 0078h 0078h 0000h 0006h 000h 0080h 0000h 742Bh 550Ch 4002h XXXXh 047Fh 0001h 0000h 0000h FFFEh Total Bytes 2 2 2 2 2 2 2 2 2 4 2 4 2 2 2 2 2 2 2 14 2 6 2 2 2 2 2 6 2 2 2 2 2 Reserved Capabilities Capabilities PIO data transfer cycle timing mode Obsolete Field Validity Current numbers of cylinders Current numbers of heads Current sectors per track mSATA SSD Identify Device Information Default Value Data Field Type Information Current capacity in sectors (LBAs)(Word 57 = LSW, Word 58 = MSW) Multiple sector setting Total number of sectors addressable in LBA Mode Reserved Multiword DMA transfer. Supports MDMA Mode 0, 1, and 2 Advanced PIO modes supported Minimum Multiword DMA transfer cycle time per word. In PC Card modes this value shall be 0h Recommended Multiword DMA transfer cycle time. In PC Card modes this value shall be 0h Minimum PIO transfer cycle time without flow control Minimum PIO transfer cycle time with IORDY flow control Reserved Serial ATA capacities Support Serial ATA Gen1 Support Serial ATA Gen2 Reserved Minor version number (ATAPI-7) Minor version number Command sets supported 0 Command sets supported 1 Command sets supported 2 Features/command sets enabled Ultra DMA Mode Supported and Selected Time required for Security erase unit completion Time required for Enhanced security erase unit completion Current Advanced power management value Master Password Revision Code Transcend Information Inc. 16 V1. 3 TS2G~16GMSA500 TS16G~64GMSA300 Word Address 93-127 128 129-159 160 161 162 163 164 165-175 176-255 Default Value 0000h 0001h 0000h 81F4h 0000h 0000h 0000h 0000h 0000h 0000h Total Bytes 70 2 64 2 2 2 2 2 22 140 Reserved Security status Vendor unique bytes Power requirement description Reserved Key management schemes supported mSATA SSD Identify Device Information Default Value Data Field Type Information CF Advanced True IDE Timing Mode Capability and Setting Reserved Reserved Reserved READ DMA (C8h) Read data from sectors during Ultra DMA and Multiword DMA transfer. A sector count of zero requests 256 sectors. READ MULTIPLE (C4h) This command performs similarly to the Read Sectors command. Interrupts are not generated on each sector, but on the transfer of a block, which contains the number of sectors defined by a Set Multiple command. READ SECTOR(S) (20h) This command reads 1 to 256 sectors as specified in the Sector Count register from sectors that is set by Sector number register. [. . . ] The host transfers 512 bytes of data, as shown in the following table, to the drive. The transferred data contains a user or master password, which the drive compares with the saved password. It is re-enabled by issuing the SECURITY SET PASSWORD command to re-set a user password. SECURITY ERASE PREPARE (F3h) Transcend Information Inc. 19 V1. 3 TS2G~16GMSA500 TS16G~64GMSA300 This command prevents accidental loss of data on the drive. mSATA SSD This command shall be issued immediately before the Security Erase Unit command to enable erasing and unlocking. SECURITY ERASE UNIT (F4h) The host uses this command to transfer 512 bytes of data, as shown in the following table, to the drive. The transferred data contains a user or master password, which the drive compares with the saved password. [. . . ]