User manual TRANSCEND CF150 DATASHEET

[. . . ] TS2G~32GCF150 TS2G~32GCF150 Description The Transcend CF 150X is a High Speed Compact Flash Card with high quality Flash Memory assembled on a printed circuit board. CF150 CompactFlash Card Features · CompactFlash Specification Version 4. 1 Complaint · RoHS compliant products · Single Power Supply: 3. 3V±5% or 5V±10% · Operating Temperature: -25 C to 85 C · Storage Temperature: -40 C to 85 C o o o o Placement · Operating Humidity (Non condensation): 0% to 95% · Storage Humidity (Non condensation): 0% to 95% · Built-in 24-bit ECC (Error Correction Code) functionality and global wear-leveling algorithm ensures highly reliable of data transfer 24bit BCH ECC (4k+208 byte per page flash) · Operation Modes: PC Card Memory Mode PC Card IO Mode True IDE Mode · True IDE Mode supports: Ultra DMA Mode 0 to Ultra DMA Mode 5(UDMA5 must work under 3. 3V), MultiWord DMA Mode 0 to MultiWord DMA Mode 4 Dimensions PIO Mode 0 to PIO Mode 6 · PC Card Mode supports up to Ultra DMA Mode 5 · True IDE mode: Fixed Disk (Standard) · PC Card Mode: Removable Disk (Standard) · Durability of Connector: 10, 000 times · MTBF: 1, 000, 000 times · Support S. M. A. R. T (Self-defined) · Support Security Command · Support Wear-Leveling to extend product life · Compliant to CompactFlash, PC Card Mode, and ATA standards · Support Global Wear-Leveling, Static Data Refresh, Early Retirement, and Erase Count Monitor functions to extend product life Transcend Information Inc. 1 V1. 0 TS2G~32GCF150 TS2G~32GCF150 CF150 CompactFlash Card Transcend Transcend Information Inc. 2 V1. 0 TS2G~32GCF150 TS2G~32GCF150 Block Diagram CF150 CompactFlash Card Transcend Information Inc. 3 V1. 0 TS2G~32GCF150 TS2G~32GCF150 Pin Assignments and Pin Type PC Card Memory Mode Pin Num 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Signal Name GND D03 D04 D05 D06 D07 -CE1 A10 -OE A09 A08 A07 VCC A06 A05 A04 A03 A02 A01 A00 D00 D01 D02 WP -CD2 -CD1 D11 1 CF150 CompactFlash Card PC Card I/O Mode Pin Num 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Signal Name GND D03 D04 D05 D06 D07 -CE1 A10 -OE A09 A08 A07 VCC A06 A05 A04 A03 A02 A01 A00 D00 D01 D02 -IOIS16 -CD2 -CD1 D11 D12 D13 D14 D15 1 1 1 1 1 1 True IDE Mode4 In, Out Type Ground Pin Num 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Signal Name GND D03 D04 D05 D06 D07 -CS0 A10 2 Pin Type In, Out Type Ground Pin Type Pin Type In, Out Type Ground I/O I/O I/O I/O I/O I I I I I I I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U I1Z I3U I1Z I1Z I1Z Power I/O I/O I/O I/O I/O I I I I I I I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U I1Z I3U I1Z I1Z I1Z Power I/O I/O I/O I/O I/O I I I I I I I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3Z I1Z I3U I1Z I1Z I1Z Power -ATA SEL A09 A08 A07 2 2 2 VCC A06 A05 A04 A03 2 2 2 2 I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I1Z I1Z I1Z I1Z I1Z I1Z I1Z I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 OT3 Ground Ground I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U Ground I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I1Z I1Z I1Z I1Z I1Z I1Z I1Z I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 OT3 Ground Ground I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3U Ground I I I I I I I I/O I/O I/O O O O I/O I/O I/O I/O I/O I O I1Z I1Z I1Z I1Z I1Z I1Z I1Z I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 ON3 Ground Ground I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 I3Z Ground A02 A01 A00 D00 D01 D02 -IOCS16 -CD2 -CD1 D11 D12 D13 D14 D15 1 1 1 1 1 1 D121 D13 D14 D15 1 1 1 1 -CE2 -CE2 -CS1 -VS1 -VS1 -VS1 Transcend Information Inc. 4 V1. 0 TS2G~32GCF150 TS2G~32GCF150 PC Card Memory Mode Pin Num 34 Signal Name -IORD 10 HSTROBE 11 HDMARDY -IOWR STOP 36 37 38 39 40 41 10, 11 CF150 CompactFlash Card PC Card I/O Mode In, Out Type I3U Pin Num 34 Signal Name -IORD 10 HSTROBE 11 -HDMARDY -IOWR STOP 10, 11 True IDE Mode4 In, Out Type I3U Pin Num 34 Signal Name -IORD 8 HSTROBE 9 -HDMARDY -IOWR STOP 7 8, 9 7 Pin Type I Pin Type I Pin Type I In, Out Type I3Z 35 I I O I3U I3U OT1 Power 35 36 37 38 39 40 41 I I O I3U I3U OT1 Power 35 36 37 38 39 40 41 I I O I3Z I3U OZ1 Power -WE READY VCC -CSEL -VS2 RESET -WAIT 10 5 -WE -IREQ VCC -CSEL -VS2 RESET -WAIT 10 5 -WE 3 INTRQ VCC -CSEL -VS2 -RESET IORDY 7 8 I O I I2Z OPEN I2Z I O I I2Z OPEN I2Z I O I I2U OPEN I2Z ON1 42 -DDMARDY DSTROBE O OT1 42 -DDMARDY DSTROBE O OT1 42 -DDMARDY DSTROBE O 11 11 9 OT1 13 43 -INPACK -DMARQ 12 O I OT1 I3U 43 44 -INPACK -DMARQ -REG DMACK 12 12 O OT1 43 DMARQ 6 O OZ1 44 45 46 47 48 49 50 -REG -DMACK BVD2 BVD1 D08 D09 D10 1 12 I O O I/O I/O I/O I3U OT1 OT1 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground 44 45 46 47 48 49 50 -DMACK -DASP -PDIAG D08 D09 D10 1 I I/O I/O I/O I/O I/O I3U I1U, ON1 I1U, ON1 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground O O I/O I/O I/O OT1 OT1 I1Z, OZ3 I1Z, OZ3 I1Z, OZ3 Ground 45 46 47 48 49 50 -SPKR -STSCHG D08 D09 D10 1 1 1 1 1 1 1 GND GND GND Note: 1) These signals are required only for 16 bit accesses and not required when installed in 8 bit systems. However, because it is not pulled upon the card in these modes, it should not be left floating by the host in PC Card modes. In these modes, the pin should be connected by the host to PC Card A25 or grounded by the host. 6) If DMA operations are not used, the signal should be held high or tied to VCC by the host. [. . . ] This bit is also set when an interface CRC error is detected in True IDE Ultra DMA modes of operation. Bit 6 (UNC): this bit is set when an Uncorrectable Error is encountered. Bit 2 (Abort) This bit is set if the command has been aborted because of a CompactFlash Storage Card status condition: (Not Ready, Write Fault, etc. ) or when an invalid command has been issued. Bit 0 (AMNF) This bit is set in case of a general error. Transcend Information Inc. 51 V1. 0 TS2G~32GCF150 TS2G~32GCF150 CF150 CompactFlash Card Feature Register (Address - 1F1h[171h]; Offset 1, 0Dh Write Only) This register provides information regarding features of the CompactFlash Storage Card that the host can utilize. This register is also accessed in PC Card modes on data bits D15-D8 during a write operation to Offset 0 with -CE2 low and -CE1 high. Sector Count Register (Address - 1F2h[172h]; Offset 2) This register contains the numbers of sectors of data requested to be transferred on a read or write operation between the host and the CompactFlash Storage Card. If the value in this register is zero, a count of 256 sectors is specified. If the command was successful, this register is zero at command completion. If not successfully completed, the register contains the number of sectors that need to be transferred in order to complete the request. Sector Number (LBA 7-0) Register (Address - 1F3h[173h]; Offset 3) This register contains the starting sector number or bits 7-0 of the Logical Block Address (LBA) for any CompactFlash Storage Card data access for the subsequent command. 6. 1. 5. 5 Cylinder Low (LBA 15-8) Register (Address - 1F4h[174h]; Offset 4) This register contains the low order 8 bits of the starting cylinder address or bits 15-8 of the Logical Block Address. Cylinder High (LBA 23-16) Register (Address - 1F5h[175h]; Offset 5) This register contains the high order bits of the starting cylinder address or bits 23-16 of the Logical Block Address. Drive/Head (LBA 27-24) Register (Address 1F6h[176h]; Offset 6) The Drive/Head register is used to select the drive and head. It is also used to select LBA addressing instead of cylinder/head/sector addressing. Bit 7: this bit is specified as 1 for backward compatibility reasons. It is intended that this bit will become obsolete in a future revision of the specification. Bit 6: LBA is a flag to select either Cylinder/Head/Sector (CHS) or Logical Block Address Mode (LBA). In Logical Block Mode, the Logical Block Address is interpreted as follows: LBA7-LBA0: Sector Number Register D7-D0. It is intended that this bit will become obsolete in a future revisions of the specification. If the obsolete functionality is support by a CF Storage Card, the CompactFlash Storage Card is set to be Card 0 or 1 using the copy field (Drive #) of the PCMCIA Socket & Copy configuration register. Transcend Information Inc. 52 V1. 0 TS2G~32GCF150 TS2G~32GCF150 CF150 CompactFlash Card Bit 3 (HS3): when operating in the Cylinder, Head, Sector mode, this is bit 3 of the head number. Bit 2 (HS2): when operating in the Cylinder, Head, Sector mode, this is bit 2 of the head number. Bit 1 (HS1): when operating in the Cylinder, Head, Sector mode, this is bit 1 of the head number. Bit 0 (HS0): when operating in the Cylinder, Head, Sector mode, this is bit 0 of the head number. [. . . ] Value 0 1 Maximum PC Card I/O UDMA timing mode Supported PC Card I/O UDMA mode 0 supported PC Card I/O UDMA mode 1 supported 69 V1. 0 Transcend Information Inc. TS2G~32GCF150 TS2G~32GCF150 2 3 4 5 6 7 PC Card I/O UDMA mode 2 supported PC Card I/O UDMA mode 3 supported PC Card I/O UDMA mode 4 supported PC Card I/O UDMA mode 5 supported Reserved Reserved CF150 CompactFlash Card Bits 11-9: Maximum PC Card Memory UDMA timing mode supported Indicates the Maximum PC Card Memory UDMA timing mode supported by the card when bit 15 is set. Value 0 1 2 3 4 5 6 7 Maximum PC Card Memory UDMA timing mode Supported PC Card Memory UDMA mode 0 supported PC Card Memory UDMA mode 1 supported PC Card Memory UDMA mode 2 supported PC Card Memory UDMA mode 3 supported PC Card Memory UDMA mode 4 supported PC Card Memory UDMA mode 5 supported Reserved Reserved Bits 14-12: PC Card Memory or I/O UDMA timing mode selectedIndicates the PC Card Memory or I/O UDMA timing mode selected by the card. Value 0 1 2 3 4 5 6 7 PC Card Memory or I/O UDMA timing mode Selected PC Card I/O UDMA mode 0 selected PC Card I/O UDMA mode 1 selected PC Card I/O UDMA mode 2 selected PC Card I/O UDMA mode 3 selected PC Card I/O UDMA mode 4 selected PC Card I/O UDMA mode 5 selected Reserved Reserved Bit 15: PC Card Memory and IO Modes Supported This bit, when set, indicates that the PC Card UDMA support values in bits 11-6 are valid. When this bit is cleared, PC Card Memory and IO Modes are not supported by the device. Idle - 97h or E3h This command causes the CompactFlash Storage Card to set BSY, enter the Idle mode, clear BSY and generate an interrupt. [. . . ]