User manual TRANSCEND TS128MJF-DSC

[. . . ] 4 Digital Camera Function Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Charging the Camera Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When you use your JetFlash as a Digital Camera for the very first time, you'll need to charge the battery approximately two (2) hours before taking pictures. You will hear a beep. While charging, the Power LED will blink with a red light. 4. After the battery is fully charged, the Power LED will stop blinking and turn off. Verify you have installed the Win98 drivers from the enclosed Driver CD before initial use in a Windows 98SE computer. See the "Driver Installation for Windows 98SE" section for Power On Pull down (open) the Power Switch (Lens Cover) until the Lens is revealed. If the Power LED is blinking red, the power is low and you need to recharge your JetFlash. You will hear a Power Off Pull up (close) the Power Switch (Lens Cover) until the Lens is covered. The Power LED light -6- Always close the camera lens cover of your JetFlash when not taking pictures. This will conserve power and protect the camera lens. Taking Pictures 1. Open the lens cover to power on your JetFlash and verify the Power LED is solid (red). Keep your JetFlash steady and press the shutter button all the way down to capture and store your picture. When you use your JetFlash for the very first time, you must charge the battery approximately two (2) hours before taking pictures. Pictures cannot be taken when your JetFlash is connected with your computer. The JetFlash image files are stored in JPEG format as below: \DCIM\100-IMG\Img-xxxx. jpg where xxxx is a JPEG file number (0001 to 9999) When the Memory LED is off, your JetFlash can only take one more picture at the most. free up storage space, you must transfer and store your pictures onto your computer. To When you connect your JetFlash to your computer via the USB port, the computer operating system will -7- Status Indications Indications Beep Buzzer Double Beep Solid Power LED (Red) Blinking Off Memory LED (Green) Solid Off Picture taken Full power Low Power Power off Space available for pictures Not enough space available for pictures Status JetFlash is powered on View / Transfer Pictures in Windows 1. (Verify you have installed the Win98 drivers from the enclosed Driver CD before initial use in a Windows 98SE computer. this time. You can copy, move, delete, or rename any files at 5. After viewing, refer to the "Safely Remove Your JetFlash" section to unplug your JetFlash. To enhance the image quality or edit your pictures, refer to the "Photo Explorer 8. 0" section -8- for detailed instructions. View / Transfer Pictures in Mac OS 1. Double-click on the Disk icon of your JetFlash, and select DCIM \ 100-IMG to access your pictures. 3. this time. You can copy, move, delete, or rename any files at 4. [. . . ] Transcend JetFlash must be used with devices that conform to the recommended industry standards. Transcend will not be liable for damages resulting from a third party device that causes the Transcend product to fail. Transcend shall in no event be liable for any consequential, indirect, or incidental damages, lost profits, lost business investments, lost goodwill, or interference with business relationships as a result of lost data. Transcend is also not responsible for damage or failure of any third party equipment, even if Transcend has been advised of the possibility. [. . . ]