User manual TRANSCEND TS128MCF45I QUICK INSTRUCTION GUIDE

[. . . ] 1 1 2 2 Driver Installation Driver Installation for Windows 98SE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Driver Installation for Windows Me, 2000, and XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Driver Installation for Mac OS 9. 0 or Later. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Driver Installation for Linux Kernel 2. 4 or Later . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To exit MP3 mode, press and hold the PLAY/PAUSE button until the Power/Play LED turns off. 6 To Remove JetFlash in Windows 98SE Unplug JetFlash from your system directly when data are not transferring. To Remove JetFlash in Windows Me, 2000, and XP 1. Click the icon on the system tray. 2. The Safely remove USB Mass Storage Device pop-up menu will appear. Click to continue. 3. A message box appears: The `USB Mass Storage Device' device can now be safely removed from the system. To Remove JetFlash in Mac OS Drag and drop the Disk icon corresponding to JetFlash into the trashcan. Then unplug JetFlash from the USB port. To Remove JetFlash in Linux Execute umount /mnt/JetFlash to un-mount the device. 7 Product Overview REC Button PLAY/PAUSE Button Record LED Power/Play LED Repeat LED USB Connector Cover HOLD Switch Microphone Earphone Jack Track Control Wheel Volume Control Wheel Basic Operation Enter MP3 Mode 1. Press and hold the PLAY/PAUSE button for a few seconds to power on (enter MP3 mode). To exit from MP3 mode, press and hold the PLAY/PAUSE seconds till the LED turns off. button for a few seconds to power on (the button for a few seconds to enter Record mode. The button until the To resume MP3 mode, press and hold the PLAY/PAUSE Record LED turns off. 8 Play a Track Press the PLAY/PAUSE button after entering MP3 or Record mode. If there is no track in your JetFlash, the Power/Play LED turns green. Pause a Track Press the PLAY/PAUSE button when there is track playback. To resume track playback, press the PLAY/PAUSE button again. Advance to Next Track Roll the Track Control Wheel toward NEXT . The Repeat LED blinks orange at fast speed, and music playback continues. again to tag the end of the portion you wish Press the Volume Control Wheel to repeat. The Repeat LED blinks orange at slow speed, and the tagged portion is played as a continuous loop. To resume normal playback, press the Volume Control Wheel For more operating instructions, please refer to Basic Operation. Press and hold the PLAY/PAUSE button for a few seconds to power on (enter MP3 mode). 7. Press and hold the REC button for a few seconds to enter Record mode. If there are bad blocks in the flash memory chip of JetFlash, the memory size of JetFlash after running the Recovery program will be smaller than the original memory size. To Recover JetFlash in Windows 98SE 1. button, then plug JetFlash into an available 13 Do not release the PLAY/PAUSE completed. 4. button until the Recovery procedures are Found New Hardware and New Hardware Found messages appear. (Only the first time you recover the JetFlash. ) 5. Click the Recovery button on the JetFlash splash screen. 6. MSCN Format status bar message appears. If above message does not appear, click the Recovery button on the JetFlash splash 14 button to screen again. If this still doesn't work, press and hold PLAY/PAUSE re-plug JetFlash first. [. . . ] When I roll the Volume Control Wheel to increase the volume, my JetFlash turns off. Why does the Power/Play LED turn on when recording voice and then JetFlash turns off 2 minutes later?A12: JetFlash is full and there is no memory available for voice recording. To make memory available for voice recording, delete some files or folders from JetFlash. [. . . ]