User manual TOYSINMOTION PRICELESS

[. . . ] Owners Manual Priceless TM from Visit toysinmotion. com for updates, attachments and all the latest news. Copyright 2004-2006, Toys In Motion, Inc. Made in China Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Male and female configurations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] While holding the vent down lightly, you should be able to slide the tab back and forth in the slot on the side of the extension. While doing so, notice holes in the vent move in relation to the holes in the extension. As you make the adjustment you will feel the key in the extension engage the ratchet slots on the underside of the vent. This is so that when you screw the Fleshlight into the extension, the vent will maintain its position along with the vacuum that you set. You will have to experiment with the vacuum to find the position you prefer. Initially, we suggest you set the vent so that the holes are perfectly aligned and the vacuum is minimal. Remove the Fleshlight insert from its housing/canister, and screw it into the extension firmly. It will bottom out against the smooth face of the vent in the extension where vacuum is maintained. In the clockwise direction, the Fleshlight will simply unscrew itself when the machine is in operation if it was not first installed tightly enough. WARNING ­ IT IS IMPORTANT THE FLESHLIGHT BE TIGHLY SCREWED INTO THE EXTENSION SO THAT IT WILL NOT COME LOOSE WHEN THE MACHINE IS OPERATED IN A CLOCKWISE DIRECTION. The shuttle should be at the bottom of transmission (as shown in the figure for step 4 in the "Assembling the base unit") with the screwdriver or drill firmly attached to both the hex drive and the cradle by means of the strap. The extension should be aligned such that the snap-catches on the extension align with the recess cut-away in the shuttle. Make this alignment and push the extension into the shuttle as far as possible and then rotate the extension clockwise. If you do not have the screwdriver or drill 7 Toys in Motion attached as instructed, the shuttle will tend to turn and retract as you try and push the extension into the shuttle making the insertion more difficult. When engaged properly, you should not be able to remove the extension without depressing the snap-catches and reversing the process unless using exceptional force. WARNING ­ IT IS IMORTANT THAT BOTH SNAP-CATCHES BE FULLY ENGAGED AND THAT THE EXTENSION CANNOT BE REMOVED Removal requires that you depress the snap-catches, rotate the extension counterclockwise, and pull. Some women with very small hands will have difficulty pressing the snap-catches in far enough to allow the extension to be rotated back to its proper withdrawal position. We apologize for this difficulty but to make the attachment strong enough to handle the inertia of a two pound Fleshlight moving 5 miles per hour necessitated this design. Install the short stand-off tube by sliding it over the Fleshlight and onto the tapered edge of the funnel. It should be snug, but it should slide all the way up to the lip on the funnel. Assemble the Fleshlight itself by installing the Fleshlight insert you intend to use. WARNING ­ USE ONLY INSERTS INTENDED FOR USE WITH THE FLESHLIGHT AND MANUFACTURED BY INTERACTIVE LIFE FORMS (www. fleshlight. com). WARNING ­ CHECK ONE LAST TIME THAT THERE ARE NO BURS, SHARP EDGES, OR ANYTHING THAT MIGHT CUT OR IRRITATE YOU SKIN, KEEPING IN MIND THE FLESHLIGHT CASE WILL BE BOTH ROTATING AND STROKING. [. . . ] If adding lubrication did not solve the problem, you may need to tighten the clutch. Adjusting the clutch 1. To remove the shuttle assembly, follow the disassembly procedures on page 12. Using an ordinary flat blade screwdriver, tighten (turn clockwise) this screw 1/8th of a turn. Repeat steps 1-4 as necessary until the machine operates normally. Gear Clutch Screw Fork WARNING ­ DO NOT OVER-TIGHTEN THE CLUTCH. [. . . ]