User manual TOSHIBA W727

[. . . ] SQPB Video Cassette Recorder W-727 OWNER'S MANUAL ABLE BOX ONTROL 3 SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. CAUTION: Product Name: Video Cassette Recorder Model Number: W-727 FCC Notice: "Declaration of Conformity". [. . . ] · If you record satellite channels, finish the DSS® satellite receiver set-up (pages 36 ­ 38), and turn on the DSS® satellite receiver. Timer Programming Procedure POWER VCR TV CH/TRK 1 4 7 I. SELECT 2 5 8 0 3 6 TV VOL Number buttons Example: To record cable channel 25 in the SP tape speed from 9:20 p. m. Today is August 25. RECORDING 9 100 DISPLAY REMAIN/ COUNTER COUNT RESET TV/ VCR 10 FF PLAY/x2 STOP ENTER 1 2 3 Load a cassette with the safety tab attached. Select "PROGRAM" using FF or REW, and press ENTER. SP/ SLP REC PLAY/x2 TIMER SLOW PAUSE/STILL CURSOR REW STOP FF PROG. CANCEL ENTER CABLE BOX CH VCR Plus+ A. SELECT EJECT CM SKIP POWER REW 4 2, 9 Move to the next using FF, and select the channel number 25 by pressing number buttons 2 and 5, PLAY/x2 or STOP. · To record a cable program from the connected cable box: Enter the cable channel number by number buttons, PLAY/x2 or STOP. If your cable box is not remote-controllable, choose the desired channel (1 to 125) on the cable box. · To record a satellite program from the connected DSS® satellite receiver: Enter the satellite channel number (100 to 999) by number buttons, PLAY/x2 or STOP. (If a number 1 to 99 is entered, the VCR will record a TV/CATV program on the channel, not a satellite's. ) If your DSS® satellite receiver is not remote-controllable, choose the desired channel (100 to 999) on the DSS® satellite receiver. · You can make "L1" or "L2" appear on the channel number position by pressing I. SELECT depending on your connection. To make corrections: Press REW to move back to the item, or FF to forward. (Continued) 25 Timer Program Recording (continued) 5 Move to the next using FF, and set the recording date using PLAY/x2 or STOP. The date changes as follows: 8/25 9/25 . . . MO~FR WKLYSA [WKLYSU]. . . [WKLYSA]: You can record TV programs on the same channel on the day and time every week. [MO~FR]: You can record TV programs on the same channel on the day and time Monday through Friday. 6 Move to the next using FF, and set the hour and minutes of the recording start time. P M 7 Move to the next, and set the recording off time. 8 Move to the next, and select the tape speed (SP) using PLAY/x2 or STOP. For the tape speed "AUTO (Auto Speed Select)", see below. To set another program, press FF, and select the next line pressing STOP. Repeat steps 4 to 8. SP 9 10 Auto Speed Select Press PROG. . Now programming is completed. Press both TIMER simultaneously. The power turns off and the VCR enters the timer standby mode. REC TIMER TIMERHi-Fi STEREO L If you are not sure the tape is long enough for timer program recording in the SP tape speed, set the recording tape speed to "AUTO". Recording starts in the SP tape speed and the VCR automatically selects the tape speed to record the program to the end. If the tape length is not long enough, the tape speed automatically changes from SP to SLP. Notes · Make sure that the tape length is selected correctly according to the tape used on the SET UP screen (page 22). · When the SLP tape speed is selected and the tape length is not sufficient to record the program to the end, the program cannot be recorded to the end. · The picture will be distorted when playing the part where the recording tape speed is switched from SP to SLP with the Auto Speed Select feature. SAP 26 Confirming the timer programs Press PROG. The screen for confirming will appear. If a power failure occurs during the timer program recording (including VCR Plus+ C 3 ® system recording (page 30) · When a power failure has occurred, the programmed contents are not effected, reset the clock P M P M Overlaps of the programs If two timer programs overlap, the recording start time of program 1 has priority over the recording off time of program 2. Program 1 (Start time) Press PROG. again to exit from confirmation page. Changing/cancelling the timer programs. 1) If the TIMER indicator is lit, press both TIMER to turn it off, and then turn the VCR on by pressing VCR POWER. To cancel a program, select the program you want to cancel in step 4, and press CANCEL. 3) Press both TIMER to return to the timer standby mode. Program 2 (Start time) Overlapped portion (not recorded) RECORDING Error indication The "--E--" ( Error ) indicator appears in the VCR display if you press both TIMER when: ­­ a cassette is not loaded. In these cases, a recording can not be made. To Cancel the Timer Recording By pressing the POWER button on the front panel of the VCR , it will cancel the timer recording and go to standby. 27 RECORDING VCR Plus+ C3 ® system Set-up VCR Plus+ C 3 ® system is a timer recording system for an easier programming that requires you only to enter a PlusCode® programming number assigned to a desired program. This section explains the necessary set-up to make VCR Plus+ C 3 ® system recordings. The flow chart below will give you an idea as to what must be done to use the VCR Plus+ C 3 ® system feature. [. . . ] (2) You must notify an Authorized TACP/THI Service Station within thirty (30) days after you discover a defective product or part. (3) All warranty servicing of this product must be made by an Authorized TACP/THI Service Station. (4) These warranties are effective only if the product is purchased and operated in the U. S. A or Puerto Rico. Set up, adjustment of customer controls and installation of repair or antenna systems are not covered by this warranty. [. . . ]