User manual TOSHIBA USB 2.0 PORT REPLICATOR II

[. . . ] 15 7 EVACUATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 8 ELECTRICAL WORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 9 APPLICABLE CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 10 TEST OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Upon approval of the customer, install the air conditioner in a place that satisfies the following conditions. Place where a sufficient servicing space can be ensured for safety maintenance and check. Place exposed to air with high salt content (seaside area), or place exposed to large quantities of sulfide gas (hot spring). (Should the unit be used in these places, special protective measures are needed. ) Place exposed to oil, vapor, oil smoke or corrosive gas. Place where the discharged air blows directly into the window of the neighboring house. (For outdoor unit) Place where noise of the outdoor unit is easily transmitted. (When installing the air conditioner on the boundary with the neighbor, pay due attention to the level of noise. ) Place with poor ventilation. (Before air ducting work, check whether value of air volume, static pressure and duct resistance are correct. ) Installation space Secure the specified space in the figure for installation and servicing. Ensure there is sufficient space to install the unit and to perform maintenance work as and when required. Keep 15 mm or more for clearance between top plate of the indoor unit and the ceiling surface. Installation space 15 or more 1000 or more 15 or more 1000 or more 283 or more 1000 or more Obstacle EN 4 283 or more ADVICE Set a service check opening panel at right side of the unit (size: 450 450 mm or more) for piping, maintenance, and servicing. Ceiling height Model RASM10SMUV-E, M10SMUCV-E, M13SMUV-E, M13SMUCV-E M16SMUV-E, M16SMUCV-E Possible installed ceiling height Up to 2. 7 m Up to 3. 5 m DEUTSCH How to set the High ceiling switch Remove the cover of the electric parts box by taking off the mounting screws (3 positions) and pushing the hooking section. Do not strap the unit in positions other than stated. EN 6 1000 or more 15 or more 1000 or more 595 to 660 Ceiling open dimension Sensor part 595 to 660 Ceiling open dimension Obstacle Check port (!450) Drain-up standing-up size Bottom face of ceiling Note As ABS is used for the drain discharge port of the main unit, the vinyl chlor paste cannot be used. Use the flexible hose (Band fix) included in the package. 368. 5 Knockout for fresh air intake 100 (diam. ) 700 Panel external dimension 145. 5 Bottom face of ceiling 595 to 660 Ceiling open dimension 525 Hanging bolt pitch Drain discharge port Hanging bolt M10 or W3/8 local arrange 220. 5 145. 5 Bottom face of ceiling 595 to 660 Ceiling open dimension 700 Panel external dimension 575 Unit external dimension 162 (diam. ) 510 Hanging bolt pitch 177 97. 5 162 (diam. ) For branch duct knockout square hole 150 (diam. ) Electric parts box 320. 5 Refrigerant pipe (Liquid) 6. 4 (diam. ) For branch duct knockout square hole 150 (diam. ) Refrigerant pipe (Gas) 9. 5 (diam. ) (Gas) 12. 7 (diam. ) Wiring connection port 575 Unit external dimension 139. 5 190. 5 Bottom face of ceiling (RAS-M10SMUV-E, M13SMUV-E, M10SMUCV-E, M13SMUCV-E) (RAS-M16SMUV-E, M16SMUCV-E) 7 EN ###RU### ###SW### PORTUGUS ESPAOL Ceiling panel ITALIANO DEUTSCH Indoor unit Stand-up 627. 5 or less Stand-up 850 or less Space required for installation and servicing FRANAIS ENGLISH Dimensional view Ceiling opening and installation of hanging bolts Evaluate and determine the piping and wiring requirements inside the ceiling prior to the hanging of the unit. After installation place of the indoor unit has been determined, create opening in ceiling and install the hanging bolts. For the ceiling opening size and pitch for hanging bolts refer to the dimensional drawing and the supplied installation pattern. Once the ceiling void has been created, ensure that the drain pipe, refrigerant pipes, inter-connecting wires and all control wires are in place prior to installing the actual indoor unit. Hanging bolt Nut M10 or W3/8 M10 or W3/8 4 pieces 12 pieces Please procure the hanging bolts and nuts for installation of the indoor unit at local site. How to use the supplied installation pattern The installation pattern is enclosed within the packaging of the air conditioner. Existing ceiling void Use the pattern to determine the position and size of the opening and location of the hanging bolts. New ceiling void Use the pattern to determine the position of the new ceiling opening. Cut off the outside of the pattern according to size of the ceiling opening. (There is a slit on the standard opening size section. ) Install the indoor unit after installation of the hanging bolts. [. . . ] Setting the unit Remove the cover of the electric parts box by taking off the mounting screws (3 positions) and pushing the hooking section. (The cover of the electric parts box remains hanged to the hinge. ) There are the selector switches (SW02) on the P. C. No. 4 of the selector switches (SW02) is provided to select the switch of the remote controller. (OFF: A setting, ON: B setting) "B" setting "A" setting Check whether the changed remote controller can operate the indoor unit or not. Auto restart setting This product is designed so that, after a power failure, it can restart automatically in the same operating mode as before the power failure. INFORMATION How to set the Auto Restart Remove the cover of the electric parts box by taking off the mounting screws (3 positions) and pushing the hooking section. [. . . ]