User manual TOSHIBA TRX80

[. . . ] Satellite Memory Realignment If all satellites are misaligned in the same direction and by the same amount, the dish has most likely been shifted by high winds or other force. This function allows you to realign your dish to match the already stored satellite positions without having to reprogram or fine tune all of the satellites individually. Use this function ONLY if all of your satellites are misaligned in the same direction (east or west) and by the same amount. Use a channel easy for you to identify, though the picture may be poor or missing. [. . . ] Missing Odd or Even Channels If you are missing the odd or even known active channels on any or all satellites, perform the following steps. If the picture is black, the problem may be a missing subscription channel. Refer to the "Missing Subscription Channel" flowchart near the end of this booklet. If this did NOT solve the problem, put the Input Mode switch back to its original position and continue to step 6. Use the EAST and WEST keys to run the Skew number all the way down to zero and all the way up to 65. If the picture does NOT come in clear somewhere in this range, set the skew number back to what is was in step 6. d. If the picture DOES come in clear somewhere in this range, adjust the skew for the best picture. If all the channels are NOT OK, repeat the above steps to adjust the skew to what it was in step 6. d. At the bottom of the page is a picture of the back panel of your receiver. The wires are usually colored red in 13, white in 14, and black in 15. Initial Set Up Initial Set Up was performed during the original system installation and should not have to be repeated. INSTALLATION 3. 1 Ku-Sat Format 3. 2 Calibrate Ku Channel 3. 3 All Data Clear 3. 4 All Satellites Clear To access any of the functions, put the receiver into the desired mode (Auto or Program), then press the FUNCTION key. If you can not access the Program Mode, you must disable the Parental Control. 6 MISSING SUBSCRIPTION CHANNELS, 1 TUNE TO THE MISSING CHANNEL. BLACK SNOW OR SCRAMBLED Go to next page A PRESS SETUP KEY, THEN 1, AND 1 AGAIN. HIGHER YES YES IS THE "SIGNAL QUALITY" HIGHER OR LOWER THAN 85 ? LOWER NO NO FOLLOW THE "FINE TUNE A SATELLITE" INSTRUCTIONS FOR YOUR MODEL. IS THE PICTURE GOOD NOW ? RESET THE RECEIVER; UNPLUG THE AC POWER CORD. NO CONTACT YOUR SATELLITE DEALER/ INSTALLER. YES DONE 7 MISSING SUBSCRIPTION CHANNELS, 2 A From previous page SNOW OR SCRAMBLED CHANGE TO A KNOWN ACTIVE FREE CHANNEL ON THIS SATELLITE. IS THE PICTURE GOOD OR SNOW / SCRAMBLED ? SNOW OR SCRAMBLED Go to next page B GOOD C From next page IS THIS AN EVEN OR AN ODD NUMBERED CHANNEL ? EVEN ODD CHANGE TO AN EVEN NUMBERED FREE CHANNEL. IS THE PICTURE GOOD ? NO YES YES NO RESET THE RECEIVER; UNPLUG THE AC POWER CORD. IS THE PICTURE GOOD NOW ? NO FOLLOW THE "FINE TUNE A SATELLITE" INSTRUCTIONS FOR YOUR MODEL. IS THE PICTURE GOOD NOW ? YES YES NO FOLLOW THE "MISSING ODD OR EVEN CHANNELS" INSTRUCTIONS FOR YOUR MODEL. The receiver is responding poorly or intermittently to your UHF controls. [. . . ] If the tips in this operations and troubleshooting video and booklet do not help solve your problem, please consult your local satellite Dealer/Installer. Look in your local telephone directory under SATELLITE, or call the C Band Industry Group at: 1-877-CBANDTV (1-877-222-6388) for assistance in locating your nearest C band Satellite Dealer/Installer. 10 TROUBLESHOOTING THE UHF REMOTE CONTROL If you are experiencing problems with poor range or intermittent operation of your UHF remote control, try the following steps. Check that the UHF antenna is securely fitted on the remote sensor connector on the back panel of the satellite receiver. Check for possible UHF noise or interference in the your receiver's environment. [. . . ]