User manual TOSHIBA TRST-56

[. . . ] TEC Thermal Printer TRST-56 SERIES Owner's Manual Table of Contents CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Dans un environnement domestique, il peut causer des interférences radio. Auquel cas, l'utilisateur sera amené à prendre les mesures adéquates. [. . . ] NOTE: For the connectable drawers, refer to your nearest authorised TOSHIBA TEC representative. e [DC24V] (Socket connector) The built-in AC adapter supplies +24V power to the printer through this connector. Do not connect anything other than the built-in AC adapter. f[AC Inlet] The AC power cord is connected to this inlet. g [Ground terminal] The drawer interface cable's ground wire is secured to this terminal. 3- 2 4. SET UP PROCEDURE 4. 1 Requirements for Operation This printer has the following requirements: Serial interface Type · The TOSHIBA TEC POS terminal to be connected must have a serial port. · To communicate with the TOSHIBA TEC POS terminal, an RS-232C interface cable is required. 25 pins Parallel Interface Type · The TOSHIBA TEC POS terminal to be connected must have a Centronics parallel port. · To communicate with the TOSHIBA TEC POS terminal, a Centronics interface cable is required. 36 pins Interface Cables For the serial interface model, use the CBLST-50-2-QM serial printer cable available from TOSHIBA TEC or equivalent. For the parallel interface model, use the Centronics cable which satisfies the following pin configuration and the specification of the connector. To prevent the emission and receipt of electrical noise, the interface cable must meet the following requirements: · Fully shielded and fitted with metal or metalized connector housings. RS-232C cable pin configuration POS terminal side D-SUB 9-pin female PIN No. Case 2 3 8 4 5 6 Signal FG RXD TXD CTS DTR GND DSR Printer side D-SUB 25-pin male PIN No. 1 2 3 4 6 7 20 Signal FG TXD RXD RTS DSR GND DTR Centronics cable pin configuration POS terminal side D-SUB 25-pin male PIN No. 1 2-9 10 11 12 13 14 16 15 17 18-25 Signal /STROBE PD1-8 /ACK BUSY PERROR SELECT /AUTOFD /INIT /FAULT /SELECTIN GND Printer side IEEE1284-B receptacle PIN No. 1 2-9 10 11 12 13 14 31 32 36 19-30 15-18 33-35 Signal /STROBE PD1-8 /ACK BUSY PERROR SELECT /AUTOFD /INIT /FAULT /SELECTIN GND N. C. N. C. NOTE: For details of the interface cable, contact your nearest TOSHIBA TEC representative. 4- 1 4. SET UP PROCEDURE EO1-13016 4. 2 Setting up the Printer 4. 2 Setting up the Printer CAUTION!Do not place the printer close to a heater or where it may be exposed to direct sunlight. Avoid locations where the printer may be exposed to high temperature, high humidity or dust. If it should, however, do not turn ON the power until the condensation is dried. Be sure that there is adequate room around the printer for easy operation and maintenance. 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) Make sure that the printer power is turned OFF. Connect the interface cable to a TOSHIBA TEC POS terminal, and plug in the power cord to the AC outlet. [. . . ] Clean the print head element (cross hatched area in the figure on the right) with a cotton swab slightly moistened with alcohol. Clean the platen with a soft cloth moistened with alcohol. Print Head Element Caution symbol for hot surface. on the above. ) Platen 6. 1. 2 Cleaning the Covers Wipe the covers with a soft dry cloth or soft cloth slightly moistened with mild detergent. After using detergent for cleaning, be sure to wipe it off with a slightly moistened cloth. 6. 2 Removing Jammed Paper 1) 2) 3) 4) 5) 6) Turn the power OFF. [. . . ]