User manual TOSHIBA TP48C71

[. . . ] For operating safety and to avoid damage to the unit, read carefully and observe the following instructions. Provide adequate space for ventilation to avoid internal heat build-up. Do not cover rear vents or install the unit in a closed cabinet or shelves. If you install the unit in an enclosure, make sure there is adequate space at the top of the unit to allow hot air to rise and escape. [. . . ] Restoring the factory default settings Select "RESET" under the function menu. Note that this also restores other settings to the factory defaults. SEL. ADJ. EXIT RETURN 3. Adjust the bass using the and buttons. SOUND BASS TREBLE BALANCE L R SEL. ADJ. EXIT RETURN · If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reappears. 27 Screen Settings Menu Adjusting the Position, Size, Fine Picture, Picture Adj The position of the image can be adjusted and flickering of the image can be corrected. Example: Adjusting the vertical position in the normal mode 3. Adjust using the and buttons. V­POSITION Press the PROCEED button on the remote controller to display the MAIN MENU on the screen, then. . . Use the v and w buttons to select "SCREEN, " then press the PROCEED button. Default settings (when RGB/PC is selected) SCREEN : NORMAL MODE V­POSITION H­POSITION V­HEIGHT H­WIDTH : OFF AUTO PICTURE FINE PICTURE PICTURE ADJ. SEL. EXIT RETURN · If neither the or button is pressed within 5 seconds, the current setting is set and the previous screen reappears. To close the main menu, press the EXIT button once more. Information When "AUTO PICTURE" is "OFF" SCREEN : FULL MODE V­POSITION H­POSITION V­HEIGHT H­WIDTH : OFF AUTO PICTURE FINE PICTURE PICTURE ADJ. SEL. EXIT RETURN · The settings on the SCREEN menu are not preset at the factory. The mode switches as follows when the buttons are pressed: NORMAL FULL and · The mode can also be switched by pressing the "WIDE" button on the remote controller. Use the v and w buttons to select "V-POSITION". SCREEN : NORMAL MODE V­POSITION H­POSITION V­HEIGHT H­WIDTH : OFF AUTO PICTURE FINE PICTURE PICTURE ADJ. SEL. This function can be used when using the display with a computer conforming to the VESA DPMS format. · If the computer's power is not turned on or if the computer and selector tuner are not properly connected, the system is set to the off state. · For instructions on using the computer's power management function, refer to the computer's operating instructions. Power management function and POWER/ STANDBY indicator The POWER/STANDBY indicator indicates the status of the power management function. See page 32 for indicator status and description. OSD OSD ADJ. POWER MGT GRAY LEVEL CINEMA MODE RGB3 ADJ. Use the and buttons to select "ON. " The mode switches as follows each time the button is pressed: ON OFF FUNCTION : ON :1 : ON :3 : ON :1 or Restoring the factory default settings Select "RESET" under the function menu. Note that this also restores other settings to the factory defaults. OSD OSD ADJ. POWER MGT GRAY LEVEL CINEMA MODE RGB3 ADJ. To close the main menu, press the EXIT button once more. 31 POWER/STANDBY indicator Power management POWER/STANDBY Power management mode indicator operating status On Green Not activated. Description Horizontal and vertical synchronizing signals are present from the computer. Turning the picture back on Picture already on. Standby Orange Activated. Operate the keyboard or mouse. The picture reappears, but more time is required than from the standby mode. [. . . ] Depending on the type of repair required, either the service will be performed in your home or the set will be taken to the TCL Authorized Service Depot for repair and returned to your home at no cost to you. IN-HOME SERVICE ONLY APPLIES WITHIN 100 KILOMETERS OF AN AUTHORIZED TCL SERVICE DEPOT. Rental Units The warranty for rental units begins with the date of first rental or thirty (30) days from the date of shipment to the rental firm, whichever comes first. *Commercial Units Plasma displays sold and used for commercial purposes have a limited ninety (90) day warranty for all parts, labor. [. . . ]