User manual TOSHIBA TLP621-4

[. . . ] For maximum protection, repack the set as it was originally packed at the factory. In the spaces provided below, record the Model and Serial No. Serial No. Retain this information for future reference. Avoid Volatile Liquid Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time. They will mar the finish. Moisture Condensation Never operate this unit immediately after moving it from a cold location to a warm location. [. . . ] 5 4 5 Focus on the picture by turning the focusing ring. A still picture is recommended for focusing. (Continued) Operations (Continued) Notes " is displayed on the screen if the " projector does not receive any signal from the connected equipment. Due to the lamp characteristic, flickers may occasionally occur in a picture. When an RGB source is selected and no signal is sent from the computer for about 30 minutes, the projector turns to standby mode for power saving. " may be While operating the projector, " displayed on the screen. This means that the operation cannot be completed. SELECT/ADJUST ON ON/STANDBY MENU ENTER INPUT LAMP TEMP CONTENTS 22 · · ON/STANDBY Indicators Notes · Even after turning the power off, the intake and exhaust fans continue to work for about 3 minutes more to cool the inside of the projector. · Immediately after the power off, the projector may not be turned on while the LAMP indicator is flashing in green. · Before unplugging the power cord, make sure that the fans are stopped. · AUTO SET ON/STANDBY KEYSTONE MARKER POINTER PJ LASER ON/STANDBY KEYSTONE Correcting the keystone distortion A picture may be expanded on the upper side if projected upward from the projector lifted up by the foot adjuster. The projector can correct this keystone distortion automatically. L-CLICK R-CLICK MENU RGB ENTER VIDEO CAMERA · RESIZE RESET FREEZE Press KEYSTONE. The keystone distortion is corrected automatically. To correct further, make the "Keystone" adjustment on the menu. 30 Turning the power off 1) Press ON/STANDBY after using the projector. An instruction message appears. 2) Press ON/STANDBY again. The LAMP indicator turns off, and the projector turns to standby mode. (The ON idicator lights in orange. ) 3) After confirming the exhaust fan stops, unplug the power cord. The ON indicator turns off. 28 Keystone Auto set : Adjust : 30 To correct the keystone distortion automatically. To make the correction of keystone distortion beyond the automatic correction. Contrast : To adjust the contrast. Camera gain : To adjust the sensitivity of the document imaging camera. (For document imaging camera model only) Language : To select the language for displays. mode : To set the projecting orientation according to the way of installation. Scrn display : To use or disable on-screen displays. Save 34 Audio Volume : 33 Save data : To save the adjustments and settings on the menu. All preset : To restore the adjustments and setings on the menu to the factory set. Image 31 To adjust the sound volume of the speaker. Auto sync. Phase : To adjust the phase. Adjustments CONTENTS 28 Initial settings ­ Default Make the basic settings for projecting. Preparation · Display the image as explained in "Picture Projection". 21 · Set the POINTER/PJ selector to "PJ". SELECT/ADJUST ON ON/STANDBY MENU ENTER INPUT LAMP TEMP 2 Press or Language P r o j . mo d e RGB i n p u t to select Eng l i s h S t anda r d RGB . De f a u l t V i deo s i gna l Au t o S c r n d i s p l a y On Proj. [. . . ] 19 · The "Brightness", "Contrast", "Sharpness" or "Phase" adjustments are not correct. 31 32 The power turns off while using the projector. · The ambient temperature of the projection room is too high. Lower the ambient temperature of the projection room, and turn the power on. The pictures are dim. · The "Brightness" or "Contrast" adjustments are not correct. The colors are strange. · The "Color", "Tint", "R-Level", "G-Level" or "B-Level" adjustments are not correct. [. . . ]