User manual TOSHIBA TLP621

[. . . ] Avoid Volatile Liquid Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time. Moisture Condensation Never operate this unit immediately after moving it from a cold location to a warm location. When the unit is exposed to such a change in temperature, moisture may condense on the crucial internal parts. [. . . ] Unplugging the power cord at this time will shorten the lamp's duration life. The cooling fan continues to run for a while to expel the heat remaining inside. If you are in a hurry, however, you may unplug the power cord at this time. The standby mode is set. LAMP EN TE R EXIT AU TO ME NU SE T VOL / ADJ · The projector consumes about 15W of power in the standby mode. We recommend you unplug the power cord when not using the projector for long periods of time. · Be sure that the LAMP indicator has turned off before unplugging the power cord. Cutting the power by unplugging the power cord while the projector is operating or the light source lamp is being cooled will shorten the lamp's duration life. Should a fault or some other irregularity arise with this unit, unplug the power cord. · When reinserting the power plug before the lamp has cooled, please wait until the lamp has cooled sufficiently before use. When the lamp is at a high temperature, it may not light and it's life duration will be shortened. KE IN PU T YS N TO E Adjusting the picture automatically Remote control CONTENTS 33 You can adjust the optimum horizontal position, vertical position, sampling phase and sampling frequency for projecting analog RGB signals at the touch of a button. 1 2 Input full screen video signals from the input source (computer) and project the image. Adjustments may not be performed properly for images that are not displayed on the entire screen or for extremely dark images. ON / STANDBY INPUT KEYSTONE AUTO SET FREEZE MUTE PIP CALL RESIZE 2 Notes Operations AUTO SET Press AUTO SET. The horizontal position, vertical position, sampling phase and sampling frequency are adjusted automatically. The icon appears during signal processing. MENU AUTO SET VOL / ADJ ENTER CT-90106 EXIT / P. MODE · Automatic adjustment may not be performed properly for signals other than those computers' signals with which the projector is compatible. (Referred to as "sub-pictures" in this manual. ) Press PIP. A sub-picture is displayed. Press the PIP button again to turn off the sub-picture. Remote control Operations Notes ON / STANDBY INPUT KEYSTONE AUTO SET FREEZE MUTE · · · · PIP CALL RESIZE PIP MENU The PIP function cannot be used when a source other than an RGB input source is selected. The PIP function cannot be used without signals supplied from an RGB signal source. The signal source, size and display position to display sub-pictures can be changed from the menu screen. 52 VOL / ADJ ENTER CT-90106 EXIT / P. MODE Displaying Information Information on the input signal source, etc. , can be displayed. CALL CONTENTS 39 Press CALL. The information described below is displayed. The information display turns off when the CALL button is pressed again. Remote control Status display Input - current input source H-resolution - the horizontal resolution of the input signal (at RGB input) V-resolution - the vertical resolution of the input signal (at RGB input) H-frequency - the horizontal frequency of the input signal (at RGB input) V-frequency - the vertical frequency of the input signal (at RGB input) Sync - the polarity of the sync signal (at RGB input) Video mode - the color mode of the video signal (at Video, S-Video input) Signal format- the formatting of the Y/PB/PR signal (at Y/PB/PR input) Lamp time - the elapsed usage time of the lamp Version - the version of the firmware Shutter - the shutter speed of the document imaging camera (at document imaging camera input) Operations ON / STANDBY INPUT KEYSTONE AUTO SET FREEZE MUTE PIP CALL RESIZE CALL MENU VOL / ADJ ENTER CT-90106 EXIT / P. MODE Notes · The information displayed is not refreshed even if it changes. To refresh the information, turn off the information display, then turn it back on. · The information display turns off if any other operation is performed. · The "Lamp time" shows an approximate time for lamp replacement. (It should not be used as a lamp warranty time counter. ) If the time indicated here nears 1500, contact your store of purchase about obtaining a replacement lamp (TLPL55, sold separately). · The "Lamp time" can be reset when the lamp is replaced. [. . . ] · Input is not set so that it can be selected with the INPUT button. By default, only the Analog RGB and Video input modes can be selected. CONTENTS 66 Cause · The power cord is disconnected. · The ambient temperature of the projection room is too high. Correction Firmly plug in the power cord. Lower the ambient temperature of the projection room, and turn the power on. [. . . ]