User manual TOSHIBA TLP-X100

[. . . ] TLP-X100 TLP-WX100 (XGA) (WXGA) OWNER'S MANUAL In the spaces provided below, record the Model and Serial No. Retain this information for future reference. Others Maintenance Operations Preparations DATA PROJECTOR Before Using Before Using SAFETY PRECAUTIONS Before Using The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] To change the setting, follow the step 2 . 2 Use the button. or button to select the lamp power and press the button. The display · When [Auto keystone] is set to [On] in the Default setting 1 menu, the keystone distortion will automatically be corrected based on the projector placement angle. If you do not desire the automatic keystone correction, set [Auto keystone] to [Off]. Note The lamp power, if selected, will be toggled without pressing the automatically disappears in a few seconds. 6 Adjusting the screen size and focus 1 2 · When the projector is turned on the next time, the start menu does not appear upon startup. However, if [Reset all] is executed from the Default setting 2 menu p. 41 , the start menu will be displayed the next time when the power is turned on. · The language can also be set via the Display setting menu p. 37 and Lamp power via the Default setting 1 menu p. 40 . · This owner's manual assumes that English has been selected. Notes Use the zooming lever to adjust the screen size. Use the focusing lever to adjust the focus. Front 7 Adjusting the volume with the buttons The speaker volume can be adjusted when an audio signal is being input. 3 Activate the connected device. Turn on and start the connected device such as a computer. 4 Press the INPUT button. An image of the connected equipment is projected. Each time you press the INPUT button, it switches to the input of the connected equipment that is outputting video signals. 26 27 Operations · To stow the foot adjuster, hold up the projector while pressing the foot adjuster release button, then slowly lower the projector. Basic operations (Continued) Precautions · Lamp characteristics may rarely cause the brightness to fluctuate slightly. There may be black spots (pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. These are intrinsic characteristics of the technology and are not malfunctions. Using handy features Using auto setting (For computer input only) This function automatically sets up the projector to the optimum state. It sets up sampling phase, frequency and screen position, for each type of the input signal by using simple operations. Remote control Notes · A lamp is consumable item. If used for extended periods, images will appear dark, and the lamp could burn out. (The lifetime of the lamp depends on conditions of use. ) · Although this projector supports a wide range of RGB signals p. 53 , any resolutions not supported by this projector (XGA for X100, WXGA for WX100) will be expanded or shrunk, which will affect image quality slightly. To view high-quality images, set the computer's external output to XGA for X100 and WXGA for WX100. · With some models of computer having LCD displays or the like, displaying images simultaneously on the projector and the monitor's display may prevent the images from displaying properly. For information on how to turn off the LCD display, see the computer's owner's manual. · If no signal is being input from the connected equipment or signal input is stopped while projecting, the "No signal" message will appear. · If a signal not supported by the projector is input, the "Unsupported signal" message will appear. · If an unavailable operation button is pressed, the icon will appear with a beep sound (if the beep sound is set to [On]). · Moving pictures played back on computers using DVD software may appear unnatural when projected with this projector. However, it is not a malfunction of the projector. Press the remote control's AUTO SET button. The icon will appear during processing. You can set as well by selecting [Auto setting] in the Image adjustment menu p. 35 . [. . . ] The · After there is an abnormal indication, the abnormal status remains until the power cord is unplugged. Note 48 49 Others Troubleshooting If you think something is wrong, check the followings before contacting customer service. If This Happens No power Power goes out during use No picture Check · Is the power cord plugged in?(When [Auto input search] is [Off]) p. 40 · Is the mute function on?If This Happens Remote control doesn't work · · · · Check Are the remote control's batteries drained? [. . . ]