User manual TOSHIBA TLP MT3

[. . . ] Before use 1 OWNER'S MANUAL 3LCD PROJECTOR TLP-MT3E 23565237 2 Before use SAFETY PRECAUTIONS WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Before use 3 In the spaces provided below, record the Model and Serial No. Serial No. IMPORTANT PRECAUTIONS Save Original Packing Materials The original shipping carton and packing materials will come in handy if you ever have to ship your LCD projector. [. . . ] When an RGB source is selected and no signal is sent from the computer for about 30 minutes, the projector turns to standby mode for power saving. " may be While operating the projector, " displayed on the screen. This means that the operation cannot be completed. SELECT/ADJUST ON ON/STANDBY MENU ENTER INPUT LAMP TEMP · · ON/STANDBY Indicators · Correcting the keystone distortion ON/ STANDBY CALL ON/STANDBY VIDEO RESIZE MUTE MARKER RGB AUTO SET KEYSTONE FREEZE KEYSTONE A picture may be expanded on the upper side if projected upward from the projector lifted up by the foot adjuster. The projector can correct this keystone distortion automatically. MENU ENTER · Press KEYSTONE. + RESET The keystone distortion is corrected automatically. To correct further, make the "Keystone" adjustment on the menu. 26 Turning the power off 1) Press ON/STANDBY after using the projector. An instruction message appears. 2) Press ON/STANDBY again. The LAMP indicator turns off, and the projector turns to standby mode. (The ON idicator lights in orange. ) 3) After confirming the exhaust fan stops, unplug the power cord. The ON indicator turns off. (Continued) Operations (Continued) 21 2) Press MUTE again. The picture is also cut off temporarily. " To restore, press MUTE again. ON/ STANDBY Contents of displayed items [ St a t us ] I npu t S i gna l Sc r e en : RGB : XGA6 0 : XGA6 0 CALL AUTO SET FREEZE CALL RGB VIDEO Note If you press MUTE while the menu is displayed, the menu disappears. MUTE Synch r o . : V 0 1 / R0 1 AUTO SET KEYSTONE RESIZE FREEZE MUTE MARKER Freezing the picture Press FREEZE. The picture freezes. Any other operations can also release the picture. MENU ENTER - + RESET Adjusting the image automatically An image which is flickering, blurred or is not centered, can be adjusted automatically. Press AUTO SET. The image is adjusted automatically. 27 Displaying the input source information Press CALL. The current input source and the signal status information is displayed. To close the display, press CALL again. Current input source Signal system of the input source Signal system automatically detected by the projector (Mode determination 36 ) Synchronizing polarity of input signal P=Positive N=Negative Version number of software Note If you press CALL while the menu is displayed, the menu disappears. Cutting off the picture and sound temporarily 1) Press MUTE. The sound is cut off temporarily. (Continued) 22 Operations When the picture size is smaller than the projection area: : To move the picture upward : To move the picture down : To move the picture leftward : To move the picture rightward RESIZE (Continued) ON/ STANDBY CALL RGB VIDEO AUTO SET KEYSTONE RESIZE FREEZE MUTE MARKER MENU ENTER - + RESET RESET , , , When the picture size is larger than the projection area: : To view the upper side of the picture : To view the lower side of the picture : To view the left side of the picture : To view the right side of the picture Notes · Picture size returns to normal after the power is turned off. may be slightly inferior in quality at the initial size because they are enlarged. · The picture returns to the normal position when the RESET button is pressed after the picture is moved. · The picture may not be projected properly while moving the picture. Changing the picture size Pictures are projected at the maximal projection size regardless of the signal types. Optionally you can change the picture size to through size or enlarge it. Press RESIZE. Each time the button is pressed, the picture size changes from the center of the picture. When the picture size does not correspond with the projection area, the picture can be moved by pressing , , and . Adjustments 23 H-position : To shift the image position horizontally V-position : To shift the image position vertically. Clock : To adjust the clock frequency. Settings and adjustments on the menu Most of adjustments and settings are made on the menu. To display the menu, press MENU. Default 24 Picture 28 The followings are adjustments and settings on the menu. When using this projector for the first time, see "Default". [. . . ] 17 · The "Brightness", "Contrast", "Sharpness" or "Phase" adjustments are not correct. 27 28 Before calling service personnel Check the following points before asking for support service. 31 The power does not come on. · The power cord is disconnected. 14 The power turns off while using the projector. · The ambient temperature of the projection room is too high. [. . . ]