User manual TOSHIBA TLP B2

[. . . ] CONTENTS 1 Before use OWNER'S MANUAL 3LCD DATA PROJECTOR TLP-B2U SAFETY PRECAUTIONS WARNING: CONTENTS 2 TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL ONLY. Before use The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. FCC NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] 29 " " is displayed on the screen if the projector does not receive any signal from the connected equipment. Due to the lamp characteristic, flickers may occasionally occur in a picture. While operating the projector, " " may be displayed on the screen. " " is displayed on the screen if: - The projector is too hot. Turn the projector off, and leave it for a while, and then turn it on again. - The ambient temperature is too high, use the projector under moderately cold temperature. " " is displayed on the screen if the air filter is dusty, the ventilation is impaired. 55 Turning the power off CONTENTS 28 1 2 Press ON/STANDBY after using the projector. An instruction message appears. Press ON/STANDBY again. The LAMP indicator turns off, and the projector turns to standby mode. (The ON indicator lights in orange. ) Operations ON LAMP ON LAMP ON (Orange) LAMP (Off) (Orange) Flashing (Green) (Orange) Flashing (Orange) 3 Notes After confirming the LAMP indicator turns off, unplug the power cord. The ON indicator turns off. Indicators Immediately after the power off, the projector may not be turned on while the LAMP indicator is flashing in green. Even after turning the power off, the intake and exhaust fans continue to work for a while to cool the inside of the projector. (When the lamp indicator is flashing in orange. ) Before unplugging the power cord, make sure that the LAMP indicator is turned off. Correcting the keystone distortion CONTENTS 29 A picture may be expanded on the upper side if projected upward from the projector lifted up by the foot adjuster. The projector can correct this keystone distortion automatically. Operations KEY STONE Press KEYSTONE. The keystone distortion on the picture projected is automatically corrected and the fine adjustment screen of the keystone distortion correction appears. / To correct further, make the "Keystone" adjustment on the menu. 38 Cutting off the picture and sound temporarily MUTE CONTENTS 30 Press MUTE. The sound and picture are cut off temporarily. To restore, press MUTE again. Operations Freezing the picture FREEZE CONTENTS 31 Press FREEZE. The picture freezes. To release the picture, press FREEZE again. Note If you perform other operation while freezing the picture, the picture freezing operation is released. Operations Enlarging the picture size You can enlarge the picture size projected. ZOOM CONTENTS 32 Press ZOOM (+). + Each time the ZOOM (+) button is pressed, the enlargement ratio increases. / / / buttons shifts the picture part ZOOM + Operations ENTER RESET Press the RESET button to cancel the zoom operation. Notes Picture enlargement display will return to the normal size after the power turns off and on again. The picture may not be projected properly while shifting the picture. Since the electrical digital zoom system is employed, the picture quality may be degraded in accordance with the enlargement ratio. If you perform other operation, the zoom operation is cancelled. Menu screen structure Most of adjustments and settings are made on the menu screen. Quick menu and full menu are provided in the menu screen. CONTENTS 33 Quick menu QUICK MENU Contrast Brightness Phase Auto keystone FULL MENU Full menu You can set the Basic setting used frequently. 34 Picture adjustment Contrast Brightness Color Tint Sharpness You can set all kinds of setting. Contrast Brightness Phase Auto keystone FULL MENU To adjust the contrast. [. . . ] 1 Power cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 (3m) Control cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Soft case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 CONTENTS 65 The design and specifications are subject to change without notice. Trademarks NEC, PC-98 series are trademarks of NEC Corporation. [. . . ]