User manual TOSHIBA TDP-TW95

[. . . ] TDP-TW95 TDP-TW100 OWNER'S MANUAL DATA PROJECTOR Others Maintenance Operations Preparations Before Using Before Using SAFETY PRECAUTIONS Before Using 3 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this product or cords associated with accessories sold with USA only this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] While the wireless LAN is in standby, the projector can be powered on using the remote control function of the Wireless Utility. When [Wireless standby] is set to [Off], the projector cannot be powered on with the remote control function of the Wireless Utility. [Remote control] Sets a remote control code from 4 types. To switch codes, set the same code for the projector and the remote control. · You cannot operate the remote control if the codes of the projector and the remote control do not match. [Power on] Note that if [Power on] is set to [Auto], then if the power is supplied when restored after a power outage, the projector will come on. Remote control code setting for remote control Remove the battery cover and set the same remote control code switch as the projector. p. 17 (Use a screwdriver with thin tip to set. ) [Easy setup] <Auto keystone>: Switches on/off the automatic keystone distortion correction when the EASY SETUP button is pressed or when Power on Easy setup is set to ON. <Auto-setting>: Switches on/off the auto-setting function when the EASY SETUP button is pressed or when Power on Easy setup is set to ON. <Power on Easy setup>: Switches on/off the Easy setup operation when the power is turned on. [Key lock] Protect from operating errors by locking on the control panel buttons of the projector. (The remote control operations are available. ) Control panel operations are locked after the setting is done, and accordingly operation with the control panel buttons is disabled. · To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to [Off]. (In the latter case, the LAMP, TEMP, and FAN indicators light in orange for 3 seconds. ) · When Wireless or USB input is selected, the [Key Lock] cannot be set to [Off] with the [RETURN] button on the projector. Note · The Easy setup automatically switches off when [Ceiling] or [Rear ceiling] is selected for projection mode. [Lamp power] When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder. ) Set this option to use the projector, for example, at high altitude (over 1, 500 meters above sea level). · Do not set Fan mode to [High] when using the projector at a lower altitude. 42 43 Operations Using the menus (Continued) Displaying Information (Status display) This displays information about the input signal, lamp use time, etc. "Yes": displayed, "No": not displayed How to use the USB terminal The supplied wireless LAN USB adapter allows users to connect the projector to a computer via wireless communication, which supports IEEE802. 11b/g wireless LAN p. 46 . (Toshiba does not guarantee the operation of all computers that are IEEE802. 11b/g compliant. ) This projector can connect with a commercial USB memory and a USB memory card reader that are USB2. 0 compliant, a digital camera or the like and display the JPEG files saved in those devices. p. 54 (Toshiba does not guarantee the operation of all USB 2. 0-compliant devices. ) To connect or disconnect a USB device, use the following procedure: Item Projector Input Mode name Resolution Frequency Sync Signal format Video mode Lamp time Lamp reset count Total time Version Description Input source name RGB input mode [Note 1] Resolution (in dots) Sync frequency Sync signal polarity [Note 2] Y/PB/PR signal format Color method of video signal Time of lamp use [Note 3] The count for lamp replacement The total time that this projector is used. Firmware version [Note 4] Computer Y/PB/PR Video S-video Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Yes No No No No Yes No Yes Yes Yes Yes Yes No No No No No Yes Yes Yes Yes Yes Yes No No No No No Yes Yes Yes Yes Yes Wireless/ USB Yes No No No No No No Yes Yes Yes Yes Connecting USB device Plug the USB device. Make sure the orientation is correct then plug the USB device in until it stays securely. USB device Notes 1: The mode of supported RGB signals p. 87 is shown. 2: Sync signal polarity shown as P (positive) or N (negative) for [H/V]. 3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time. ) When the displayed time approaches 2, 000 hours, consult with a dealer about getting replacement for: TLPLW9 for TDP-TW95 or TLPLW10 for TDP-TW100 (sold separately). 4: [Version] shows the version of the projector's internal control program. This version is referred to for customer service, etc. q Switch the input to Wireless/USB and press the MENU button twice to display the Setting display (2), then select and run Unplug device in the Control setting menu. The processing for disconnecting a USB device starts. w The message "Safe to remove the USB device" appears on the screen. Disconnecting a USB device during operation may cause a malfunction or data corruption. Note · The displayed information will not be refreshed if the status changes. [. . . ] p. 22 Are all the connected devices functioning properly? No audio · Is the wireless LAN USB adapter card inserted correctly?The wireless LAN USB adapter · Is a wireless LAN USB adapter not supported by the projector inserted?doesn't work The operation of USB adapters other than the supplied product is not guaranteed. p. 49 · Are there any obstructions between the computer and projector? [. . . ]