User manual TOSHIBA TDP-T9

[. . . ] OWNER'S MANUAL (Getting Started) DATA PROJECTOR TDP-T9 For more details , please refer to the owner's manual of the CD-ROM version SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING: Handling the cord on this product or cords associated with accessories sold USA only with this product, will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. [. . . ] H is the height from the image bottom to the center of the lens. 23 Preparations Connection · Read the owner's manual of the device you are connecting to the projector. · Some types of computer cannot be used or connected to this projector. · The MONITOR terminal outputs analog RGB signals or component video signals (Y/PB/ PR) from the COMPUTER IN terminals as selected with the INPUT button. If no input is selected, the MONITOR terminal outputs the input signals last selected among the COMPUTER terminals. · A computer monitor usually cannot accept Y/PB/PR signals correctly. Monitor Computer (for control) Before connection To video output AV cable (not supplied) To audio input Audio cable (not supplied) To RS-232C terminal Control cable AUDIO IN MONITOR COMPUTER S-VIDEO VIDEO AUDIO OUT CONTROL RGB cable (supplied) Computer To RGB output AV cable (not supplied) To S-video output Audio cable (not supplied) To audio output Notes · Moving pictures played back on computers using DVD software may appear unnatural if it is projected with this projector, but it is not a malfunction. · When an AUDIO OUT terminal is connected, sound is not output from the projector speaker. · Output volume of AUDIO OUT terminal can be adjusted by the VOL button. 24 Turning the power on and off Connecting the power cord 1 Insert the power cord connector into the AC IN socket of the projector. 2 Insert the power cord plug into a wall or other power outlet. Removing the lens cover Power cord connector (Supplied) Be sure to remove the lens cover when the power is turned on. If it is left on, it could become deformed due to heat. The power turns on the green indicators light: Power. After a moment, the start-up screen appears. KEYSTONE + KEYSTONE - · Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes or sight. · Do not place your hands, face, or other objects near the air exhaust. Doing so could cause burns, deform/break the object. CAUTION Notes · The start-up screen will disappear after a moment. You can dismiss the start-up screen before this by performing any operation. You can also configure the start-up screen not to appear via the Display setting menu p. 34 . · The first time you use the projector after purchase, after the start-up screen disappears, the start menu is displayed p. 27 . · When [Key lock] is [On], the operation buttons of the projector do not work p. 30 . · When [Password] is [On], the start-up screen is displayed after the Password entry screen disappears p. 30 . 25 Operations Turning the power on 1 Press the ON/STANDBY button. Control panel POWER Remote Control Start-up screen Turning the power off 1 Press the ON/STANDBY button. A message appears on the screen, confirming that you wish to shut off the power. (This operation is no longer valid after the message disappears. ) 2 Press the ON/STANDBY button again. The screen turns off, but the internal cooling fan continues to operate for a short. Then , the projector goes into standby mode. When cooling lamp POWER After cooling complete POWER FLASH A B C A During cooling, the Power indicator flashes. If you are in a hurry, there is no problem with unplugging the power cord or turning off the main power switch in this state. In standby mode B Note · The projector consumes about 15W of power in standby. [. . . ] · Place the projector so that the air intake and exhaust are not blocked. · Unplug the power cord and wait for a short while, then turn the power back on. 5 second of abnormal display, the projector returns to the standby state waiting for internal cool down. 5 second of abnormal display, the projector returns to the standby state waiting for internal cool down. [. . . ]